Benutzeranleitung / Produktwartung SNCDH110W des Produzenten Sony
Zur Seite of 132
CGI Command Manual 1 Sony Netw or k Camer a SNC -CH110 , SN C -CH120 , SNC -CH 140 , SNC -CH160 SNC -CH180 , SN C -CH210 , SNC -CH 220 , SNC -CH240 SNC -CH260 , SN C -CH280 SNC - DH110 , SNC -DH110T ,.
CGI Command Manual 2 C ontents 1 About this manual .................................................................................................................................. 4 2 Motion video request commands ...................................
CGI Command Manual 3 1 1.18 Us er .......................................................................................................................................... 78 1 1.19 S ecurity ..........................................................
CGI Command Manual 4 1 About this manual This document des cribes CGI commands usage of S ony Net work Camera and Sony Video Networ k S tation . Appli cable models and version are foll owi ngs .
CGI Command Manual 5 via an equipped line out put connector . 4) Still im a ge re quest commands These are to be used to get a l at est still image from the camera. 5) Setting com m ands of camer a T hese are to be used to set pi c ture quality and so on.
CGI Command Manual 6 2 Moti on video r equest commands There are four kinds of request to acquire motion video data. /image /image1 Y ou can ac quire Bit stream corr esponding to the setup of I mageCodec1. I f " mpeg4 " is set up in I mageCodec1 , y ou can ac quire MPEG -4 bit st ream .
CGI Command Manual 7 [HTTP bit st ream] The following data shows t he way to acquire the HTTP . When simply puttin g "GET /ima ge...", "GET /mpeg4..." or "GE T /h264...", the camera wil l s end the MPEG -4 or H.264 raw data as its response.
CGI Command Manual 8 In terms of acquiri ng RTP bit stream (unicast ), putting "Ud pMode=unic as t" and "UdpPort=<UDP port number>" will be require d when sending HTTP request. UdpMode parameter S pecify a mod e of transmission which will be either "unica s t " or "multicast".
CGI Command Manual 9 [RTP (UDP) bit st r eam (multi cast)] In terms of multic ast R TP bit stream, acquiring seq uenc e is different from the unicast one. In order t o activate mult icast bit stream, getting information of the multicast settings in the camera is needed pri or to starting the se quence.
CGI Command Manual 10 Also, it is poss i bl e adjusting the frame rate by setting the "s peed" or "interval" parameter when cli ent application r eques ts bit stream.
CGI Command Manual 11 <Example> Request for motion i mage by 20 frames per second GET /mjpeg?speed=20 HT TP/1.0 ¥r¥n Host: 192.168. 1.1 Request from m ot ion image by 1 frame per second by using "i nterval" parameter GET /mjpeg?interv al= 1000 HTTP/1.
CGI Command Manual 12 2.2 Acquiring multi plexed Audio & Video bit stream The client applic ation can get audio data as well with the video bit st ream . In this case both video bit stream and audio bit s tream will be multiplexed in one TCP session.
CGI Command Manual 13 -- myboundary ¥ r¥n Content - Ty pe: audio/1 6kadpc m ¥r¥n DataLen: 320 ¥r¥n ¥r¥n <Audio chunk> ¥r¥n -- myboundary ¥ r¥n Content - Ty pe: image/j peg ¥r¥n Cam.
CGI Command Manual 14 DataLen: 000xxx x x ¥r ¥n ¥r¥n <JPEG image data> ¥r¥n -- myboundary ¥ r¥n . . . The following m odel c an't obtain voice data.
CGI Command Manual 15 3 Audio data request command In terms of audio bit s tream, the camera can also send it in t he form of "HTTP bit stream", "RTP (UDP) bit stream (unicas t)" or "R TP (UDP) bit stream (multi c ast)" like MPEG -4 bit stream.
CGI Command Manual 16 [RTP bit str eam (multicas t )] In terms of acquiri ng audio R TP bit stream (multicast), putting UdpMode=mul ticast parameter is required when it is request ed vi a HTTP . I n order to activate audio multicast bit stream, getting informat ion about the multicast s et tings is needed prior to starting the sequence.
CGI Command Manual 17 4 Audio out put r equest commands These requests are to be used for sendi ng encoded audio data to the camera in order to output audio via the equipped li ne output. Putting appropriate "B asic authorization (Authoriz ation: Basic xxxx)" hea der for this request is requi red.
CGI Command Manual 18 5 S till image request Acquire 1 data segment of JP E G fil e as a still image. This command returns a latest JPEG file on the camera. Image siz e, color reproduction setti ng and expos ure setting become the sam e as t he motion image (Image Codec 1) .
CGI Command Manual 19 6 Setting comm ands of camera p arameters Set various set t ings for the camera. When using thes e c ommands, describe as the foll owi ng syntax <parameter>=<value>. It is possible to transmit several parameters at one time only when they belon g to the same CGI name (The part of < cgi > of Syntax ).
CGI Command Manual 20 7 Inquiry com mands of camera p arameters These are to be used to inqui re current status of the camera. The item whic h has an inquiry parameter in the " 11 . CGI comm ands list" can be inquired such as its current status.
CGI Command Manual 21 <Parameter s> Refer to Chapter " 11 . CGI command list " wi th the item which has an "inq" attribute..
CGI Command Manual 22 8 Control comma nds for Panning, Tilting, Zooming and Focu sing " ptzf " command is us ed for controlling Pan, T ilt, Z oom and Foc us. The followings expl ai n " rel ative " parameter , "AbsoluteP anT ilt" parameter and " AreaZoom " parameter .
CGI Command Manual 23 03 around 2 0% 04 around 2 5% 05 around 3 0% 06 around 4 0% 07 around 5 0% 08 around 6 6.7% 09 around 8 3.3% 10 around 1 00% <Example> move right with 30% on VGA.
CGI Command Manual 24 Figure 8-2 Coordinate system of SolidPTZ Refer to " 12.15 PanMovementRange / T iltMovementRang e / ZoomMovementRange " for the range of the coordinate of pan and tilt . Thes e values can be read from the camera with P anMovementRange or T iltMovementRange of C GI command.
CGI Command Manual 25 8.4 ContinuousPanTiltZoom parameter (synt ax: Cont i nuousPanT iltZoom=<pan speed>,<tilt speed>,<zoom speed> ) This parameter is suitable for the pan and tilt opera tion which a joy sticks was us ed for .
CGI Command Manual 26 9 Configura tion command for motion object de tection or unattended object detectio n T hese are to be used f or configuring motion detect ion. Common configuration term s are described in 9.1. Inquiring the c onf iguration is described in 9.
CGI Command Manual 27 9.2 Inquiring the c onfigurat ion The configurat i on of the motion detection can be inqui re d described as section 6. Refer t o section 6 for detail.
CGI Command Manual 28 10 Information reque st command This request is to be us ed for getting information such a res ult of motion detection or status of the sensor input in the form of "HTT P bit stream". Before using t his command, you should configure as des cribed below: " AlamData " parameter in system.
CGI Command Manual 29 T amperi ng=0 ¥r¥n Audio =0 ¥r¥n --myboundary ¥r¥n Content - T ype: text/plain ¥r¥n CamT im: 2007 - 04 - 01 Sun 14:10:46 ¥ r¥n ¥r¥n ． ． （ SNT - EP104, SNT - EP154 ） GET/command/al armdata.cgiHTTP/1.1Host: 192.
CGI Command Manual 30 11 CGI command lis t These are the tables of every cat egor y of the CGI command. These CGI commands may not be able to be used by the model ( see under the each table ). < codec > of Parameter is the i nteger (1 - 3) which shows ImageCod ec 1 ～ ImageCodec3.
CGI Command Manual 31 SNT - EP154 are always "0". A m odel except for that is al ways "1". ZoomFunc "0"/ "1" syst em - 1.00 I ndicates the camera su pp orts Zoom function. S NT - EP104 and SNT - EP154 are always "0".
CGI Command Manual 32 id : display camera ID only id tim : display ti m e & camera ID tim : display time only custom : display the text defi ned b y SiFormat off : disable super impose ( For the conver t ible ) This s et up becomes effective only w hen SiEnable is "off".
CGI Command Manual 33 SNC - DH120/1 20T/160/220/220T /260 .) SiEnable SiEnableIma ge1 SiEnableIma ge2 "on"/"off" s ystem system.cgi 1.12 Enable or disa ble of Superimpose funct i on. It takes precedence over the specific at ion of SuperimposeFunc .
CGI Command Manual 34 "B ottom - left ": Bottom - right" is the same, too. (L imitation 3) Set it up in S iPosition n not to overla p. When it overlaps and it is set up, you must make the designat i on of either one side a null character s tring.
CGI Command Manual 35 areatitling : Indicat ion of an area title . SiAzimuthMode "0"/"4"/"8" sys tem system.cgi 1.00 Azimuth is set up. 0: OFF 4: 4 directio n 8: 8 direction SiAzimuthNor thPanPos <pan hex> s yste m system.
CGI Command Manual 36 <Blink> : It is always " o ff ". < St y l e > specifies the e ffect on transm i s s ion of the string. 0: outline string (other ar eas include a character b.
CGI Command Manual 37 Alarm<AO> Duration "0"t o"300" sys tem system.cgi 1.00 The time of the output of the alarm is set up. VideoOutMode "ip" / " n tsc " / " pal " sys tem system.cgi 1.00 Select video o utput mode.
CGI Command Manual 38 Model name Unsupport ed command (S ystem) SNC - C H 11 0 Alarm<A O >Duration, CameraCont rolInterface, P o werControl, RackModel Name, RackSerialN o, RackSlotId, SiAr eaTit.
CGI Command Manual 39 SiAreaT itleNum, SiAzimuthMode, SiA zimuthNorthPa nPos, SiDirectionM ode SNC - DH120 Alarm<AO> Duration, Cam er aControlInterfac e, PowerControl, R ac k ModelName, RackSe r.
CGI Command Manual 40 RoundPanor amaPict ure, SiAreaTitle, SiAreaTitleClear , SiAreaT itleNum, SiAzimuthM ode, SiAzimuthN orthPanPos, SiDirect ionMode, SiEnabl eImage1, SiEnableIma ge2, SiFontSizeIm a.
CGI Command Manual 41 11.2 Exclusive camera contr ol Parameter Val ue InqPa rm SetC GI Ver Note CamCtrlRight "on"/ "off" syst em system.cgi 1.00 On or off the exclusiv e pan/tilt control from ActiveXv ie wer . CamCtrlTime "10"to"600" s ystem system.
CGI Command Manual 42 11.4 Pan/Tilt/Zoom Parameter Value InqParm SetCGI Ver No te Move "<direction> ,<speed>,<codec > " - ptzf.
CGI Command Manual 43 AbsolutePa nT iltI mage1 AbsolutePa nT iltI mage2 RelativePanTilt "<pan position>,<tilt position>, <speed>,<codec> " - ptzf.cgi 1.12 Move in the specifie d direction . speed: " 1 " to "24" AbsoluteZoom "<zoom position> ,<codec> " - ptzf.
CGI Command Manual 44 VisibleT iltRange "<min pos > ,<max pos>" ptzf - 1.10 A n i nd ication range is return ed. ContinuousPa nT ilt Zoom "<pan speed>,<ti lt spe ed>,<zoom speed>,< codec> " - ptzf.
CGI Command Manual 45 The command which can't be used in eac h model is shown in the following table. Model name Unsupport ed command ( Pan/Tilt/Zoom ) SNC - C H 11 0 AnalogC amFocusS peed, A.
CGI Command Manual 46 SNC - DH1 10/1 10T AnalogCamFocusSpeed, AnalogCamPanSpeed, AnalogCamTiltS peed, AnalogCamZo omS peed, AutoFli p, AutoFlipMode , Horizo ntalTiltLimit, LimitPanTilt, SerialDirect S.
CGI Command Manual 47 AnalogCamTiltS peed, Analo gCamZoomS peed, A utoFlip, AutoFlipMode, Eflip, Ef lipFunc, HorizontalTiltLimit, LimitP anT ilt , S er ialDirect, SolidPT Z1, SolidPTZ 2, SolidPTZMode .
CGI Command Manual 48 RelativeZoom, SolidPTZ, SolidPT Z1, SolidPTZ2, SolidP T ZMode, SolidPTZ TiltDirection, VisibleP anR ange, VisibleT iltRange When a connected analog camera s upports it, SNT - EX101/ 101E/ 104/154 can use the foll owi ng CGI command.
CGI Command Manual 49 ・ SNC - CH180, CNC - DH140 / 140T/180/220/220T /240/240T/260/280 ： 0 – 2399 ( Integer) FzAbsoluteZF " <zoom>,<f ocus> " - focuszoom.cgi 1.00 A zoom and a f ocus are adjusted to t he abs olute value at the same t ime.
CGI Command Manual 50 Model name Unsupport ed command ( Focus/Zoom ) SNC - CH120 F zAbsoluteZoom, Fz Move, FzRelativeZF , FzRelat i v eZoom, FzZoomMov e mentRange SNC - CH140 F zAbsoluteZoom, Fz Move,.
CGI Command Manual 51 DynamicRang eCompressor "on"/" of f" camera camera.cgi 1. 10 A dynamic ran ge compression funct ion i s s et up. ImageCodec "jpeg"/"mpeg 4"/"h264" "mpeg 4- jpeg"/ "jpeg - mpeg4" "h264 - jpeg"/ "jpeg - h264" camera camera.
CGI Command Manual 52 McTtl "1"to"255" camera camera.cgi 1.00 Set TTL value on the multicast packet. UcVideoPort "1024"to "65534" camera camera.cgi 1. 00 Set the port number fr om w hic h MPEG -4 or H.264 sends in unicast streaming.
CGI Command Manual 53 camera restart s a RTSP server . M4FrameRate "<framerate>" camera camera.cgi 1.00 Set frame rate of MPEG -4 Frame Rate (fps) 0(fastest), 1 , 2, 3, 4, 5, 6, 8, 1 0, 15, 20, 25, 30 Setting Comm and a nd Inquiry Command ar e invalid when " mpeg4 " isn't specified in Im ageCodec.
CGI Command Manual 54 JpT argetRatio "5"to"60" camera camera.cgi 1.00 C om pr ession ratio is set with 1/"n". Setting Comm and i nvalid when "jpeg" isn't specified in Ima geCodec. JpBandwidth "0.0" /"0.
CGI Command Manual 55 Color "color "/"black" camera camera.cgi 1. 00 Select color video or m on ochrome video . ZoomMode "f ull"/"optical" camera camera.
CGI Command Manual 56 "full"/"shutter"/" iris"/"manual" SNC - CH140/1 80/220/240260/280 SNC - DH140/1 40T/180/220/220T /2 40/240T/ 260/280 ： "autoirisl ens"/"manualirisle ns" BLComp "on"/ "of f" camera camera.
CGI Command Manual 57 AgcMaxGain "0" t o " 7", "15" camera - 1.00 It is fi xed val ue by the model. Refer to Appendix. Gain "0" to "15 " camera camera.cgi 1.00 Adjus t gain. This is effective when ExpMod e is manual.
CGI Command Manual 58 AutoShutterM axS peed, AutoShut terMinS peed, Color, DynaView , DynamicRan geCompressor , EchoSuppressor , Ef fectiveA rea<n>, ExpCompMod e, ExpMode, Foc us Mode, Gain, Iri.
CGI Command Manual 59 SNC - CH240 B LCom p, DynaView , ExpCom pMode, FocusMode, Gain, G amma, Iris, IrisMode, Ir ismove, LineLock, Li neL ockVPhase, VideoNoiseR educ tio n, VideoPTRefresh, VideoPT R e.
CGI Command Manual 60 MicLineSelect, RTSPMcAudioPort, R TSPUcAudioPort, UcAudioPort, VideoInSt atus, VideoPT R ef resh, VideoPTRefreshInterval, VideoPTRefreshP eri od, V ideoP T RefreshSchedule, Video.
CGI Command Manual 61 SNC - DH2 80 BLComp, D ynaV iew , ExpCompM od e, FocusMode, Gain, Gamm a, Iris, IrisMode, Iris m ov e, LineLock, LineLoc k VPhase, VideoNoiseReducti o n, VideoPTRefresh, VideoPT .
CGI Command Manual 62 SNT - EX154 Agc, AgcMaxG ain, AreaSet, AspectRati oConversion, AutoShutter , AutoShutt erMaxS peed, AutoShut terMinS peed, AutoS lowShutter , Aut oSlowSh utterMinS p ee d, BGain,.
CGI Command Manual 63 PrivacyDispEach "<no.>","on"/ "off" - camera.cgi 1.00 Change on/off for each m as king area. PrivacyMaxNum <PrivacyMaxNum> fcb - 1.00 It is the num ber of masks which can be set up . The command which can't be used in eac h model is shown in the followi ng table.
CGI Command Manual 64 SNT - EP154 PrivacyPTZ<no.> , PrivacySetMask SNT - EX101 /101E PrivacyPTZ<no.> , PrivacySetMask SNT - EX104 PrivacyPTZ<no.> , PrivacySetMask SNT - EX154 PrivacyPTZ<no.> , PrivacySetMask The Privacy mask CGI commands c annot be used with the following model s .
CGI Command Manual 65 IRLedMaxStrength " 1" to "6 " camera camera.cgi 1.00 This sets up the strength of the I R ir radiation. NIRComp "on"/"off" camera camera.cgi 1. 10 Near - IR compens ation. A correspo ndi ng model is SNC - RS46/ 86.
CGI Command Manual 66 SNC - DH210/2 10T DnLevel, DnManualFunc , DnSchedule, DnS ensor<AI>, DnSt atus, DnS yncE as yFocus, DnTime, IRLed, IRLedMaxStrength, NIRComp, ViewDROffInNight, WashedOutIma.
CGI Command Manual 67 11.9 Serial Parameter Value InqParm SetCGI Ver Note SerT ype SNC - RH124/1 64 , SNC - RS4 4 /4 6 /8 4 /8 6 ： "tcpip"/"visca"/" pelco - d" SNT - EX101/ 101E/ 104/154 ： "normal"/"tcpip " serial serial.
CGI Command Manual 68 SNT - EX104 SerSrcCamId, SerT ermination SNT - EX154 SerSrcCamId, SerT ermination The Serial CGI commands cannot be used with the following models . ♦ SNC - CH1 10/120/140/160/ 180/210/220/240/260/280 ♦ SNC - DH1 10/1 10T /120/120T/140/140T/ 160/180/210/210T/220/220T/ 240/240T/260/280 ♦ SNT - EP104/ 154 11.
CGI Command Manual 69 DomainSuffix "<domai n suffix>" network net work.cgi 1.00 Set domai n suffix. HttpPort "80"/ "1024"to"65535" network network.cg i 1.00 Set http port . Mtu " 1000 " to " 1500 " network network.
CGI Command Manual 70 11.11 Wireless n etw ork Parameter Value InqParm SetCGI Ver Note WirelessFunc "on" / "off" wireless wireless.cgi 1.00 WlsDhcp "on" / "off" wirel ess wireless.cgi 1.00 WlsDnsAuto "on" / "off" wireless wireless.
CGI Command Manual 71 " wpaeaptkip "/" wpa2eapaes "/ "wpap sktkip"/" wpa2 pskaes " / "wps" WlsWpsPinnumber " <number> " wireless wireless.cgi 1.00 WlsWpsExec " on " - wireless.
CGI Command Manual 72 11.12 Filtering Parameter Value InqP arm SetCGI Ver Note FilterFuncG UI " on/off " sys tem system.cgi 1.00 V 4FilterFunc " on/of f " filter filter .cgi 1.00 V 4FilterDef aultRule " allo w/deny " filter filter .
CGI Command Manual 73 11.13 QoS Parameter Value InqParm SetCGI Ver Note V 4MangleFunc " on/off " qos qos.cgi 1.00 V 4MangleDefa ultV alu e [0 - 63] qos qos.
CGI Command Manual 74 11.14 Dynamic IP address notification Parameter Value InqParm SetCGI Ver Note SmtpIpNtfyService "on"/"off" ipnot ify ipnotify .cgi 1.00 SmIpv4Ntfy "on"/ " off" ipnotify ipnotif y .cg i 1.00 SmIpv6Ntfy "on"/"off" ipnot ify ipnotify .
CGI Command Manual 75 11.15 SSL / TLS Parameter Value InqParm SetCGI Ver Note SSLMode "Plain" / "SSL" / "Plain - SS L" / "SSL- Plain" network network.cgi 1.00 SSLProtocol "SSLv23" / "SSLv3" / "TLSv1" or "TLSv10" net work network.
CGI Command Manual 76 SSLCACert< n>SubjectDn <subjec t domain name string> network - 1.00 SSLCACert< n>ExtendedKey Usage <exte nded key usage string> network - 1.00 SSLCACert< n>V alidi ty <Y YYY -MM- DD> net w ork - 1.
CGI Command Manual 77 CACert<n>S ubjectDn <subject dom ain name string> 802Dot 1X - 1.00 CACert<n>E xtendedKeyUsage < extended key usage st r i ng> 802Dot1X - 1.00 CACert<n>V ali dity <YYYY -MM- DD> 802 Dot1X - 1.00 ClientCertI nstalled "0"/" 1" 802Dot1X - 1.
CGI Command Manual 78 11.18 User Parameter Value InqParm SetCGI Ver Note Administrat or "<encoded name : p ass>" user user .cgi 1.00 User<n> " <encoded name : pass>,< mode>" user user .cgi 1.00 <n> is the integer of 1 - 9.
CGI Command Manual 79 < num > specifie s the number of "1" - "256". W hen it is completely de leted, "all" is specif ied. PresetName PresetNameI mage1 PresetNameI mage2 "<no.>,< name>,<no.>,<name>, .
CGI Command Manual 80 PresetSensor <AI>Image1 PresetSensor <AI>Image2 PresetAud "<no> "/"none" presetpos ition presetposit ion.cgi 1.10 HomePos HomePosImag e1 HomePosImag e2 "set"/"reset"/"rec all"/"ptz - recall" - presetpos ition.
CGI Command Manual 81 T our<X>Sched uleImage2 T our <X> S peed T our<X>SpeedImage1 T our<X>SpeedImage2 "<speed>" pr esetposition preset position.
CGI Command Manual 82 ST ourRsmT ime "5" to " 3600 " presetpositi on presetpositio n.cgi 1.00 ST ourRecord <A,B,C ,D, temp,stop> - presetposition.cgi 1.00 ST ourPreview <A,B,C,D, temp,st op> - presetposition. cgi 1.00 ST ourPreviewCopy <A,B ,C,D> - presetpositio n.
CGI Command Manual 83 SNC - CH160 G roupAdd, GroupClear , GroupMak e, GroupName, PresetAu d, PresetDetection, P resetGroupRegist, P resetGroupRelati o n, PresetVMF , ST our, ST our<X>, ST our<.
CGI Command Manual 84 SNC - CH280 Hom eP osImage1, HomePosI mage2, HomePosProper t yImage1, HomePos P r opertyImage2, PresetCo py , PresetNameIm age 1, PresetNameImage2, PresetPosImage1, PresetPosIm a.
CGI Command Manual 85 SNC - DH180 Hom eP osImage1, HomePosI mage2, HomePosProper t yImage1, HomePos P r opertyImage2, Pr es etCopy , PresetNameI mage1, PresetNameIma ge2, PresetPosIm a ge1, PresetPosI.
CGI Command Manual 86 SNC - DH280 Hom eP osImage1, HomePosI mage2, HomePosProper t yImage1, HomePos P r opertyImage2, PresetCo py , PresetNameIm age 1, PresetNameImage2, PresetPosIm a ge1, PresetPosIm.
CGI Command Manual 87 T ourPrevie wS peedImage 2, T ourResumeIma ge1, T ourResumeImage 2, T ourRsmTimeImage1, T ourRsmTimeImage2 SNT - EX104 HomePo sIm ag e1, HomePosImage2, Hom e PosPropertyImage 1, .
CGI Command Manual 88 FcAlmFunc "on"/"off" ftpclient ftpclient.cgi 1.00 FcAlmRemotePath "<tex t>" ftpclient ftpclient .cg i 1.00 FcAlmAssignedName "<text>" ftpclient ftpclient. cgi 1.00 FcAlmSuffix "date"/"seq" ftpclient ftpclient.
CGI Command Manual 89 FcPrdImage1 "on"/"off" ftpclient ftpclient.cgi 1. 12 FcPrdImage2 "on"/ "of f" ftpcli ent ftpclient.cgi 1. 12 SeqClear " ftp - periodical" - etc.cgi 1.00 FcManualFun c "on"/"off" ftpclient ftpclient.
CGI Command Manual 90 SNC - DH180 F cAl mIm age1, F cA lmI mage2, F cP rdI mage1, F cP rdI mage2 SNC - DH210/2 10T FcAlmAud, FcAlmBuf fer , FcAlmVmf SNC - DH220 FcAlmAu d, FcAlmBuffer , FcAlmSensor<.
CGI Command Manual 91 11.23 SMTP Parameter Value InqParm SetCGI Ver Note SmtpFunc " on"/"off" smtp smtp.cgi 1.00 SmtpPort "25"to"6553 5" smtp smtp.cgi 1.00 PopPort " 11 0 " to " 65535" smtp smtp.
CGI Command Manual 92 SmAlmT amp ering "on"/" of f" smtp smtp.cgi 1.00 SmAlmSensor<AI> "on"/"off" smtp smtp.cgi 1.00 SmAlmAud "on"/"off" smtp smtp.cgi 1.10 SmAlmPeriod "always"/"schedul e" smtp smtp.
CGI Command Manual 93 SmEmgPowerDetect "on"/"off" smtp smtp.cgi 1.10 It is informed of the change of the power supply . It can use only with S NT - EX15 4 an d SNT - EP154. SmEmgInterval "<interval time>" smtp smtp.
CGI Command Manual 94 SmEmgRcptAddr , SmEmgVideoDetect SNC - CH280 SmAlmImage1, SmAlmImage2, SmEmgAdminAddr , SmEmgFanDetect, SmEmgFunc, SmEmgInterval, SmEmgNotifyCyclic, SmEmgPowerDetect, SmEmgRcptAd.
CGI Command Manual 95 SmEmgRcptAddr , SmEmgVideoDetect, SmPrdImage1, SmPrdImage2 SNC - RH124 / 164 SmAlmImage1, SmAlmImage2, SmEmgPowerDetect, SmPrdImage1, SmPrdImage2 SNC - RS4 4/ 4 6/ 8 4/ 86 S mAlm.
CGI Command Manual 96 SmAthPassword "<text>" smtp smtp.cgi 1.00 Identic a l as the SMTP ImCapWarnRcptAddr "<e - mail a ddr >" imagememory im agememory .cgi 1.00 ImCapWarnFromAddr "<e - mail a ddr>" imagememor y imagememory .
CGI Command Manual 97 SeqClear "imagememor y - alarm" / "image me mory - periodica l" / "imagememory - manual" - etc .cgi 1.
CGI Command Manual 98 ImAlmT amper ing, ImAlmVmf, ImCapWarn, ImCapW arnFro m A ddr , ImCapWarnRcptAddr , ImDriv e, ImManAssignedNam e, ImManSuffix, ImManualFunc , ImOverWrite, ImPeriodi calFunc, ImPrd.
CGI Command Manual 99 SNT - EP154 ImAlm Aud, ImAlmSensor<AI>, I mAlmT ampering, ImAlmVmf 11.25 Edge storage Parameter Value InqParm SetCGI Ver Note EdgeS torage "on " /"off" edgestora ge edgestorage.cgi 1. 10 An EdgeStorage function is tur ned on and off.
CGI Command Manual 100 EsAlmRec<ch>T ime " <pre time> , <post time> " edgestorage edgestor age.cgi 1. 10 It is time to r ecord it. EsAlmRecMaxT ime<codec> " <pre time>,< post time> " edgestorage - 1.
CGI Command Manual 101 11.26 Alarm out Parameter Value InqParm SetCGI Ver Note AlarmOut<AO> Func "on"/" of f" alarmo ut <AO> alarmout .cgi 1.00 Ao<AO> Mode "alarm"/ "timer"/"daynight" alarm out <AO> alarmo ut.
CGI Command Manual 102 SNC - DH260 Ao<AO> AlmAud , Ao<AO> AlmVmf The Alarm out CG I commands c annot be used with the following models .
CGI Command Manual 103 ♦ SNT - EP104/154 When a sound is reproduced with CH1, it is output in Audio Out in SNT - EX154. It isn't output in Audio Out even if a sound is reproduced with CH2 - CH4. 11.28 Alarm buffer Parameter Value InqParm SetCGI Ver Note AlmBufT ime "<pre time>, <post time>" alarmbuffer alarmbuffer .
CGI Command Manual 104 ODPre<XXX> Win <YY> " on "/" o ff " objec t detectio n objectdetection.cgi 1.00 Enable or disable window . ODPre<XXX> Win <YY> Mode " det "/"mask" objectdetection objectdetect ion.
CGI Command Manual 105 Od <MM> CandidateFrame "3"to"7" objectdetecti on objectdetection. cgi 1.00 Rough time from an objec t appears in the scene to the object is detected. If you turn down this value, the o bject is detected more quickl y , b ut false alarm increases .
CGI Command Manual 106 Objectdetection funct i on for the new case. 11.30 VMF Parameter Value InqParm SetCGI V er No te VmfPassing<XXX >< YY> Name <name> vmf objectdetection .cgi 1.00 Set up the nam e of the passing detection filter .
CGI Command Manual 107 VmfExiting<XXX >< YY>Area <numbe r>,<x1>,<y1 >,<x2>,<y2>,... vmf obj ectdetection.cgi 1.00 < number >: Number of area <x>,<y>: C oordin ate of area VmfExiting<XXX >< YY> MinSize <x>,<y> vmf objec t detectio n.
CGI Command Manual 108 Combo < ZZZZ > Duration <time >,<time>,... combo objectdetection. cgi 1.00 Set up the durat ion of the co mpound detect ion filter . Combo < ZZZZ > Logic " and "/" or " combo objectdetect ion.
CGI Command Manual 109 LOD MinObjectSize "small"/" middle "/" large " lod lod.cgi 1.00 Set up t he minimum size of the obj ect. LOD Sensitivit y "0" to " 100 " lod lod.c gi 1.00 Set up the sen sitivity .
CGI Command Manual 11 0 When the setti ng is restored, all - co nfiguration.cgi or al l - configuration - pres et.cgi is used. 11.35 T rigger Parameter Value InqParm SetCGI Ver Note T rigger " ftp" - main.cgi 1.00 T rigger " ftp - alarmbuffer" - main.
CGI Command Manual 111 voicealert< n> -t est SNC - CH220 ft p - alarmbuffer , mem ory , mem ory - alarmbuffer , voi c eal ert<n>, voicealer t <n> - test SNC - CH260 ft p - alarmbuffe.
CGI Command Manual 11 2 System=initiali ze .) Format "buil tin" - main.cgi 1.00 Builtin memory w ill be for m atted. Delete "home p age"/"v oicealert" - main.cgi 1.00 "voicealert" : All voicealert file will b e deleted.
CGI Command Manual 11 3 SNT - EP104 Ao<AO>Status , Sensor <AI> SNT - EP154 Ao<AO> S tatus, Sensor <AI>.
CGI Command Manual 11 4 12 A ppendix 12.1 Image Size The image siz e which can be chosen is shown in t he table of the bottom. There may be a li mitation in the image size whic h can be chosen by the image 1 an d the image 2. Furthermore , it may depend on setting of maximum image s ize.
CGI Command Manual 11 5 Image Size （ width x height ） SNC - CH110 SNC - DH110/1 10T SNC - CH120/1 40/160/180 SNC - DH120/1 20T/140/140T/160/1 80 *3 16:9 4:3 1280x720 1280x1024 1280 x 1024 1280.
CGI Command Manual 11 6 Ima ge Size （ widt h x h eight ） SNC - CH210 SNC - DH210/2 10T SNC - CH220/2 60 SNC - DH220/2 20T/260 SNC - CH240/2 80, SNC - DH240/2 40T/280 *3 16:9 4:3 1920x1080 1920x144.
CGI Command Manual 11 7 12.2 AreaSet Model Settings Maximum Size ( widt h x heig ht) R ange of AreaSe t SNC - C H 11 0 SNC - DH1 10/1 10T Aspect Ratio : 4: 3 1280 x 960 1, 1, 1280, 960 Aspect Ratio : .
CGI Command Manual 11 8 12.4 ImageMaxSize Model Settin gs ImageM axSize SNC - C H 11 0 SNC - DH1 10/1 10T Aspect Ratio : 4: 3 1280x960 Aspect Ratio : 16: 9 1280x720 SNC - CH120/1 40/160/180 SNC - DH12.
CGI Command Manual 11 9 12.7 AgcMaxGain Model A gcM axGain SNC - CH 11 0 SNC - DH1 10/1 10T "0" to "4" (6, 12, 18, 24, 30dB) SNC - CH120/1 60/210 SNC - DH120/1 20T/160 "0".
CGI Command Manual 120 12.9 WBMode Value SNC - CH 1 10/1 20/140/160 / 180/210/2 20 / 240/260/280 SNC - DH 1 10/1 10T /120/120T/140/140T /160/ 180 / 210/210T /220/220T /2 40/240T/ 260/280 SNC - RH124/1.
CGI Command Manual 121 12.11 Vi ew mode<mode> bit viewermode function descrip tion Full PanTilt Preset Light Vie w 0 1 1 1 1 1 - Reser ved. 1 1 1 1 1 1 Ti me Display time. 2 1 1 1 1 1 Vo l ume Display vol ume. 3 1 1 1 1 0 View Size Display vie w er s iz e button.
CGI Command Manual 122 12.13 Shutter Speed, Iris, Gain, ExpComp SNC - RH124/164 Shutter Speed Iris Gain ExpComp Value NTSC(se c) PAL(Sec) Valu e (F) Valu e (dB) Value (EV) 1 2 3 4 5 6 7 8 9 10 11 12 1.
CGI Command Manual 123 SNC - RS44 /84 Shutter Speed Iris Gain ExpComp Value NTSC(se c) PAL(Sec) Valu e (F) Valu e (d B) Valu e (EV) 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 1 1/2 1/4 1/.
CGI Command Manual 124 SNC - RS46 /86 Shutter Speed Iris Gain ExpComp Value NTSC(se c) PAL(Sec) Valu e (F) Valu e (dB) Value (EV) 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 1 1/2 1/4 1/8 .
CGI Command Manual 125 SNC - CH140/180/24 0 , SNC - DH140/140T/180/ 240/240T Shutter Speed ExpComp Value (sec) V alue (EV) 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 1 1/2 1/4 1/8 1/15 1/30 1/50 1/60 1/100 1/250 1/500 1/1000 1/2000 1/4000 1/10000 0 1 2 3 4 5 6 7 8 9 10 11 12 - 2.
CGI Command Manual 126 SNC - CH1 10, SNC - DH1 10/1 10T Shutter Speed Value (sec) 1 2 3 4 5 6 7 8 9 10 11 12 13 14 1/2 1/4 1/8 1/15 1/30 1/50 1 /60 1/100 1/250 1/500 1/1000 1/2000 1/4000 1/10000 12.
CGI Command Manual 127 12.15 PanMovementRange / T iltM ovementRange / ZoomMovementRange Model Setting s Pan Movement Range T ilt Movement Range Zoom Movement Range SNC - CH120/1 60/ SNC- DH120/120T /160 Max .
CGI Command Manual 128 SNC - RS44 / 84 Value (Optical Zoom Position Data) Zoom Ratio Value (Digital Zoom Position Dat a) Digital Zoom Rati o 0000 1606 2151 2860 2CB5 3060 32D3 3545 3727 38A9 3A42 3B4B.
CGI Command Manual 129 SNC - RS46 / 86 Value (Optical Zoom Position Data) Zoom Ratio Value (Digital Zoom Position Dat a) Digital Zoom Ratio 0000 166F 1FF0 257D 2940 2C02 2E2B 2FEE 316A 32B2 33D4 34D9 .
CGI Command Manual 130 12.17 Focus （ expected value ） SNC - RH124/164 Focus Position 1000 ～ C0 00 Far end Near end Focus Near Li mit 1000 : Over Inf 2000 : 4.5m 3000 : 2.0m 4000 : 1.2m 5000 : 80cm 6000 : 45cm 7000 : 38cm 8000 : 15cm 9000 : 7.0cm A000 : 3.
CGI Command Manual 131 SNC - RS46/86 Focus Position 1000 ～ C0 00 Far end Near end Focus Near Li mit 1000 : Over Inf 2000 : 20m 3000 : 10m 4000 : 5m 5000 : 3cm 6000 : 2m 7000 : 1.5m 8000 : 32cm 9000 : 9.5cm A000 : 4.5cm B000 : 2cm C000 : 1cm Left listed value m a y be shi fted by thermal conditions.
CGI Command Manual 132 Revision history Version Date Comment 0.9 Jun.17,2 009 P rov is ional edition 0.91 Jul.17,2 009 P rovisiona l edition 0.92 Aug.21,2 009 P rovi s i o nal edition 1.00 Sep.17,2 009 Added command of m otion video request c om mands Some parameter add it ion and the change of the valu e.
Ein wichtiger Punkt beim Kauf des Geräts Sony SNCDH110W (oder sogar vor seinem Kauf) ist das durchlesen seiner Bedienungsanleitung. Dies sollten wir wegen ein paar einfacher Gründe machen:
Wenn Sie Sony SNCDH110W noch nicht gekauft haben, ist jetzt ein guter Moment, um sich mit den grundliegenden Daten des Produkts bekannt zu machen. Schauen Sie zuerst die ersten Seiten der Anleitung durch, die Sie oben finden. Dort finden Sie die wichtigsten technischen Daten für Sony SNCDH110W - auf diese Weise prüfen Sie, ob das Gerät Ihren Wünschen entspricht. Wenn Sie tiefer in die Benutzeranleitung von Sony SNCDH110W reinschauen, lernen Sie alle zugänglichen Produktfunktionen kennen, sowie erhalten Informationen über die Nutzung. Die Informationen, die Sie über Sony SNCDH110W erhalten, werden Ihnen bestimmt bei der Kaufentscheidung helfen.
Wenn Sie aber schon Sony SNCDH110W besitzen, und noch keine Gelegenheit dazu hatten, die Bedienungsanleitung zu lesen, sollten Sie es aufgrund der oben beschriebenen Gründe machen. Sie erfahren dann, ob Sie die zugänglichen Funktionen richtig genutzt haben, aber auch, ob Sie keine Fehler begangen haben, die den Nutzungszeitraum von Sony SNCDH110W verkürzen könnten.
Jedoch ist die eine der wichtigsten Rollen, die eine Bedienungsanleitung für den Nutzer spielt, die Hilfe bei der Lösung von Problemen mit Sony SNCDH110W. Sie finden dort fast immer Troubleshooting, also die am häufigsten auftauchenden Störungen und Mängel bei Sony SNCDH110W gemeinsam mit Hinweisen bezüglich der Arten ihrer Lösung. Sogar wenn es Ihnen nicht gelingen sollte das Problem alleine zu bewältigen, die Anleitung zeigt Ihnen die weitere Vorgehensweise – den Kontakt zur Kundenberatung oder dem naheliegenden Service.
