Benutzeranleitung / Produktwartung L1632E des Produzenten Snapper
Zur Seite of 36
OPERA T OR’S MANU AL Lar g e Frame Sno wthr o wer s 1226 Models Mfg. No. Description 1695324 L1226E, Snowthrower 1695325 L1226EX, Snowthrower (CE) 1695326 L1226E, Snowthrower 1695327 L1226EX, Snowthrower (CE) 1428 Models Mfg.
T able of Contents 1 CONTENTS: Safety Rules & Inf ormation General ............................................................2 T raining ............................................................4 Preparation ..................................
2 TP 600-3606-05-LW-SMA Operating Safety Congratulations on purchasing a superior-quality piece of lawn and garden equipment. Our products are designed and manu- factured to meet or exceed all industry standards for safety. Power equipment is only as safe as the operator.
3 Moving Parts This equipment has many moving parts that can injure you or someone else. However, if you are standing in the operator’s position, and follow all the rules in this book, the unit is safe to operate. The auger and impeller have spinning parts that can amputate hands and feet.
4 This machine is capable to amputating hands and feet and throwing objects. Read these safety rules and follow them closely. Failure to obey these rules could result in loss of control of unit, severe personal injury or death to you, or bystanders, or damage to property or equipment.
5 8. Always follow the engine manual instructions for stor- age preparations before storing the unit for both short and long term periods. 9. Always follow the engine manual instructions for proper start-up procedures when returning the unit to service.
Decals 6 DECALS This unit has been designed and manufactured to pro- vide you with the safety and reliability you would expect from an industry leader in outdoor power equipment.
Decals 7 Part No. 1733059 - DANGER / WARNING Main Dash Decal, CE, w/o Easy Turn Part No. 1733060 - DANGER / WARNING Main Dash Decal, CE, w/ Easy Turn Part No. 1733772 Shift Decal Part No. 1727208 Auger Danger Decal Part No. 1727207 Discharge Chute Danger Decal Part No.
Safety Icons 8 WARNING: READ OPERATOR’S MANUAL. Read and understand the Operator’s Manual before using this machine. DANGER: THROWN OBJECTS. This machine is capable of throwing objects and debris. Keep bystanders away. WARNING: REMOVE KEY BEFORE SERVICING.
Identification Numbers 9 When contacting your authorized dealer for replace- ment parts, service, or information you MUST have these numbers. Record your model name/number, manufacturer’s identi- fication numbers, and engine serial numbers in the space provided for easy access.
10 Features, Controls, & Operation CONTR OL LOCA TIONS The information below briefly describes the function of individual controls. Starting, stopping, and driving require the combined use of several controls applied in specific sequences. To learn what combination and sequence of controls to use for various tasks see the OPERATION section.
Features & Controls 11 Starter Electric Start: Depressing the starter button activates the electric starter. The electric start button operates on 120 Volts AC, which is provided by connection to the extension cord provided. Connect this extension cord ONLY to a properly grounded 3 prong electrical outlet.
Operation 12 GENERAL OPERA TION CHECKS BEFORE EA CH ST ART -UP 1. Make sure all safety guards are in place and all nuts, bolts and clips are secure. 2. Check to make sure that the clean-out is attached to the auger housing. Do not operate the machine with- out the clean-out tool properly stored on the auger housing.
Operation 13 ST ARTING CONTR OLS See Figure 1 for the following instructions. Electric Start A. Electric Start Button - The Electric Start Button (A) activates an electric starter mounted to the engine, eliminating the need to pull the starter han- dle.
Operation 14 ST ARTING THE ENGINE W ARNING Rapid retraction of starter cord (kickback) will pull hand and arm toward engine faster than you can let go. Broken bones, fractures, bruises or sprains could result. When starting engine, pull the starter cord slowly until resistance is felt and then pull rapidly to avoid kickback.
Operation 15 D C E B F A Figure 3. Engine Start/Stop A. Throttle Control Lever B. Fuel Shut-Off Valve C. Safety Key D. Choke Control Knob E. Primer Button F. Starter Cord Handle 9. Electric Start: First connect the extension cord to the power cord receptacle (A, Figure 4) and then into a wall receptacle.
16 Operation CLEARING A CLOGGED DISCHARGE CHUTE IMPORT ANT NO TE Hand contact with the rotating auger/impeller inside the discharge chute is the most common cause of injury associated with snowthrowers. DO NOT use your hand to clean out the discharge chute.
17 Operation GR OUND SPEED SELECT OR Use the speed selector (A, Figure 5) to control the drive speed of the snowthrower. There are six forward speeds and two reverse speeds. Use the lower speeds to blow deep or wet snow. Use the higher speeds to blow light snow or to drive the snow- thrower without blowing snow.
Operation 18 EASY TURN™ FREEWHEELING AND TRA CTION DRIVE LOCK While Clearing Snow: For easy turning when using the snowthrower, squeeze the Easy Turn™ lever (Figure 8). Engaging the Easy Turn™ lever releases the left traction wheel but allows the right wheel to continue driving (Figure 8).
Operation 19 W ARNING Never store the unit, with gasoline in engine or fuel tank, in a heated shelter or in enclosed, poor- ly ventilated enclosures. Gasoline fumes may reach an open flame, spark or pilot light (such as a furnace, water heater, clothes dryer, etc.
20.
21 Regular Maintenance A UGER GEAR CASE LUBRICA TION 1. Place the snowthrower on a level surface. 2. Remove the pipe plug (A, Figure 11). 3. Check the lubricant level. It should be level with the lower edge of the plug opening. If not, add Benalene grease.
LUBRICA TION Remove wheels and grease axles once each year. Apply 5W-30 synthetic motor oil to the friction disk drive hex shaft (A, Figure 13). Apply medium weight (10W) oil to points shown (See Figures 12-15). Generally, all moving metal parts should be oiled where contact is made with other parts.
23 Regular Maintenance CHECK / LUBRICA TE FREE-HAND LINKA GE Check the function of the Free-Hand controls. The con- trols should function as described in the CONTROLS section. It is critical for the safe operation of the unit that the controls disengage when released.
24 T roubleshooting, Adjustments, & Service W ARNING Before performing any adjustment or service to snowthrower, stop the engine and wait for mov- ing parts to stop. Remove the key. To prevent accidental starting, disconnect the spark plug wire and fasten away from the plug.
T roubleshooting 25 Prob lem P ossible Cause Remedy Auger rotates, but snow is not- thrown far enough. Chute deflector too low. Adjust deflector as necessary. Engine speed too slow. Set speed to full throttle. Ground speed too fast. Use slower speed selector setting.
Adjustments 26 A UGER DRIVE ADJUSTMENT 1. Check that the auger cable (A, Figure 18) is on top of cable button (B) as show in Figure 18. 2. With the drive lever released, the hook (B, Figure 19) should barely touch the lever (C) without raising it. There can be a maximum 1/32” clearance as shown.
27 Adjustments 4. Slide the cable boot (A) over the cable adjustment bracket. Run-In Adjustment ALL MODELS 1. After 5 hours of use, check for proper adjustment. Readjust clutch cable if necessary by increasing ten- sion on cable. A small amount of arm movement is permissible if unit passes operating checks described in the Warning above.
28 Adjustments Figure 23. Cable Adjustment A. Adjustment Nut B. Jam Nut A B Figure 24. Belt Cover A. Belt Cover B. Screws A B B Figure 25. Auger Belt Deflection A. Engine Drive Pulley D. Nut B. Idler Pulley (Engaged) E. Auger Belt C. Auger Drive Pulley B C A 1/2” (12.
Adjustments & Service 29 Figure 26. Shear Pins A. Shear Pins B. Cotter Pins A B A B SHEAR PIN REPLA CEMENT Under most circumstances, if the auger strikes an object which could cause damage to the unit, the shear pin will break. (This protects the gear box and other parts from damage.
Service 30 BEL T REPLA CEMENT A uger Drive Belt The drive belts are of special construction and must be replaced with original factory replacement belts available from your nearest authorized service center. Some steps require the assistance of a second person.
31 Adjustments & Service Figure 32. Frame and Axle Housing A. Upper Capscrews B. Lower Capscrews C. Auger Housing D. Frame B Figure 30. Spout Rotator Rod A. Special Nut B. Cover C. Hair Pin D. Spout Rotator Rod A B C D A B D A D C Figure 31. Install Spout Rotator Rod A.
32 Service T raction Drive Belt If the snow thrower will not move forward, check the trac- tion drive belt for wear or damage. If the traction drive belt is worn or damaged, replace the belt as follows. 1. Disconnect the spark plug wire. 2. Remove the auger drive belt.
Specifications 33 ENGINE: 1100 Series Briggs & Stratton Make Briggs & Stratton Model Snow Series, M15H Gross Torque* 11.00 ft-lbs (14.9 Nm) @ 3060 rpm Displacement 15.2 cu. in (249 cc) Oil Capacity 19 oz. (,56 l) 1350 Series Briggs & Stratton Make Briggs & Stratton Model Snow Series Max, M20H Gross Torque* 13.
Parts & Accessories REPLA CEMENT P ARTS Replacement parts are available from your authorized dealer. Always use genuine Simplicity / Snapper Service Parts. TECHNICAL MANU ALS Additional copies of this manual are available, as well as fully illustrated parts lists.
© Copyright 2007, BRIGGS & STRATTON. All Rights Reserved. Printed in USA. MANUFACTURING, INC. 500 N Spring Street / PO Box 997 Port Washington, WI 53074-0997 www.
Ein wichtiger Punkt beim Kauf des Geräts Snapper L1632E (oder sogar vor seinem Kauf) ist das durchlesen seiner Bedienungsanleitung. Dies sollten wir wegen ein paar einfacher Gründe machen:
Wenn Sie Snapper L1632E noch nicht gekauft haben, ist jetzt ein guter Moment, um sich mit den grundliegenden Daten des Produkts bekannt zu machen. Schauen Sie zuerst die ersten Seiten der Anleitung durch, die Sie oben finden. Dort finden Sie die wichtigsten technischen Daten für Snapper L1632E - auf diese Weise prüfen Sie, ob das Gerät Ihren Wünschen entspricht. Wenn Sie tiefer in die Benutzeranleitung von Snapper L1632E reinschauen, lernen Sie alle zugänglichen Produktfunktionen kennen, sowie erhalten Informationen über die Nutzung. Die Informationen, die Sie über Snapper L1632E erhalten, werden Ihnen bestimmt bei der Kaufentscheidung helfen.
Wenn Sie aber schon Snapper L1632E besitzen, und noch keine Gelegenheit dazu hatten, die Bedienungsanleitung zu lesen, sollten Sie es aufgrund der oben beschriebenen Gründe machen. Sie erfahren dann, ob Sie die zugänglichen Funktionen richtig genutzt haben, aber auch, ob Sie keine Fehler begangen haben, die den Nutzungszeitraum von Snapper L1632E verkürzen könnten.
Jedoch ist die eine der wichtigsten Rollen, die eine Bedienungsanleitung für den Nutzer spielt, die Hilfe bei der Lösung von Problemen mit Snapper L1632E. Sie finden dort fast immer Troubleshooting, also die am häufigsten auftauchenden Störungen und Mängel bei Snapper L1632E gemeinsam mit Hinweisen bezüglich der Arten ihrer Lösung. Sogar wenn es Ihnen nicht gelingen sollte das Problem alleine zu bewältigen, die Anleitung zeigt Ihnen die weitere Vorgehensweise – den Kontakt zur Kundenberatung oder dem naheliegenden Service.
