Benutzeranleitung / Produktwartung PZ40X des Produzenten Nikon
Zur Seite of 10
NE 使用説明書 INSTRUCTION MANUAL ISTRUZIONI MANUAL DE USUARIO English Italiano Español 日本語.
Please read and follow these essential safety procedures to prevent accidents, injury to yourself and others, as well as property damage. Read all these instructions carefully to insure the safe use of your Sunpak flash unit. W ARNING Do not attempt to open, repair , or modify this unit.
3 Welcome to the worldwide family of Sunpak Owners. Y our Sunpak PZ40X is specially designed for NIKON AF-SLRs as well as some Nikon type digital cameras.
Description of Parts Flashtube Housing Accessory (optional) Mounting Guide Battery Compartment Cover Autofocus Infrared Flash Knurled Lock Ring Dedicated/Hot Shoe Contact LCD Display Bounce angle disp.
Installing the batteries 5 1. Before installing the batteries, please check that the power switch is in the "OFF" position. T o unlock the battery compartment, push lightly on the center of the cover . 2. T o open the battery compartment slide the cover back (toward the rear of the unit) as shown.
TTL Mode 3D Multi Flashing Mode (3D MULT-Mode) Manual Mode Press the Mode Select Button Press the Zoom button With A-group cameras, repeated pressing of the mode button will cycle the flash display from 3DMUL T Mode to TTL and through the manual power ratio settings, returning to the 3DMUL T Mode.
7 With digital cameras (such as the Nikon D-100), both TTL Autoflash Mode and Manual Mode are available. Please refer to Page 6. When taking a picture, the Ready light blinks at first and then lights steadily .
There are five power-output settings available with the PZ40X in manual mode, from full power to 1/16 power . First, push the Mode Selector button continually until “M” is displayed. The flash will t hen be in the Manual mode. Please refer to the Chart 1 on page 15 for details on setup.
9 Auto OK When the subject is within the Auto Effective Range and there is enough light, the "Auto OK" symbol in the LCD display will blink for about 2 seconds after the flash has been fired. If the symbol goes out, then there was not enough light for an exposure.
Continuous Use Do not use the flash continuously for more than the number of times stipulated in the table below , in order to prevent damage to the unit. Once the maximum number of flashes has been reached, allow the flash to rest for at least 10 minutes before using it again.
Ein wichtiger Punkt beim Kauf des Geräts Nikon PZ40X (oder sogar vor seinem Kauf) ist das durchlesen seiner Bedienungsanleitung. Dies sollten wir wegen ein paar einfacher Gründe machen:
Wenn Sie Nikon PZ40X noch nicht gekauft haben, ist jetzt ein guter Moment, um sich mit den grundliegenden Daten des Produkts bekannt zu machen. Schauen Sie zuerst die ersten Seiten der Anleitung durch, die Sie oben finden. Dort finden Sie die wichtigsten technischen Daten für Nikon PZ40X - auf diese Weise prüfen Sie, ob das Gerät Ihren Wünschen entspricht. Wenn Sie tiefer in die Benutzeranleitung von Nikon PZ40X reinschauen, lernen Sie alle zugänglichen Produktfunktionen kennen, sowie erhalten Informationen über die Nutzung. Die Informationen, die Sie über Nikon PZ40X erhalten, werden Ihnen bestimmt bei der Kaufentscheidung helfen.
Wenn Sie aber schon Nikon PZ40X besitzen, und noch keine Gelegenheit dazu hatten, die Bedienungsanleitung zu lesen, sollten Sie es aufgrund der oben beschriebenen Gründe machen. Sie erfahren dann, ob Sie die zugänglichen Funktionen richtig genutzt haben, aber auch, ob Sie keine Fehler begangen haben, die den Nutzungszeitraum von Nikon PZ40X verkürzen könnten.
Jedoch ist die eine der wichtigsten Rollen, die eine Bedienungsanleitung für den Nutzer spielt, die Hilfe bei der Lösung von Problemen mit Nikon PZ40X. Sie finden dort fast immer Troubleshooting, also die am häufigsten auftauchenden Störungen und Mängel bei Nikon PZ40X gemeinsam mit Hinweisen bezüglich der Arten ihrer Lösung. Sogar wenn es Ihnen nicht gelingen sollte das Problem alleine zu bewältigen, die Anleitung zeigt Ihnen die weitere Vorgehensweise – den Kontakt zur Kundenberatung oder dem naheliegenden Service.