Benutzeranleitung / Produktwartung NEAX2000IPS des Produzenten NEC
Zur Seite of 48
D TERM ® SERIES i T elephone USER GUIDE NEAX ® 2000IPS NEC-403 DtermSeries i UG Insid6 1/23/03 12:31 PM Page I.
L IABILITY D ISCLAIMER NEC A MERICA , I NC . RESERVES THE RIGHT TO CHANGE THE SPECIFICATIONS , FUNCTIONS , OR FEATURES , AT ANY TIME , WITHOUT NOTICE . NEC A MERICA , I NC . HAS PREPARED THIS DOCUMENT FOR USE BY ITS EMPLOYEES AND CUSTOMERS . THE INFORMATION CONTAINED HEREIN IS THE PROPERTY OF NEC A MERICA , I NC .
T ABLE OF CONTENTS K EYS AND L AMPS 2 T ERMINAL S ETUP W ITH THE F EATURE K EY 7 T O O RIGINATE AN O UTSIDE C ALL V IA E XTENSION L INE K EY 8 T O O RIGINATE AN I NTERNAL C ALL 9 O UTSIDE L INE A PPEA.
KE YS AND LAM PS F UNCTION K EYS Hold Press key to place an internal or external call on hold. T ransfer Allows the station user to transfer established calls to another station, without attendant assistance. Speaker Controls the built- in speaker which can be used for Hands Free dialing / monitoring.
Message T o search Message W aiting. Directory Press key to display the directory of Dial by Name for Station Speed Dialing. UP / DOWN ( ▲▼ ) Used to adjust LCD contrast, speaker / receiver volume, and ringer volume. ◆ LCD Contrast: Press ▲ or ▼ key while idle.
FD-B (Call Forwarding – Busy) Press key to activate, verify , or cancel Call Forwarding – Busy feature. FD-N (Call Forwarding – No Answer) Press key to activate, verify , or cancel Call Forwarding – No Answer feature. FD-DS (Call Fowarding – Destination Set) Press key to activate Call Forwarding – Destination.
5 S OFT K EYS (F ACTORY A SSIGNED F EA TURES ) Headset Press the Soft Key below “Headset” to activate or deactivate Headset operation. Help Press the Help Key . Press desired Soft Key for helpful information about that key . Exit Press the Exit Key to exit the Help program.
T O U SE T HE H ELP K EY ◆ Press the HELP key and the Soft Key . ◆ Explanation of the pressed Soft Key is indicated on the LCD. ◆ Press the EXIT key to leave Help. L AMPS Call Indicator Lamp Lamp at top corner of D t e rm Display flashes when a call terminates to the terminal.
7 TERMINAL SET UP WITH THE FEA TURE KEY M ICROPHONE O N /O FF The MIC lamp shows the status of the built-in microphone. T o change microphone status: ◆ Press MIC key . T O S ELECT R INGER T ONE The Dterm Series i has eight kinds of ringer tones that you can select.
◆ Press 3 . The LCD displays the selected tone number (n=1~8). ◆ Press 3 . Next tone is selected. T O PRESET RINGER VOLUME NOTE: Access to feature is based on data assignment. ◆ Press Feature and 0. Ringer activates. ◆ Press ▼ or ▲ key . Ringer volume decreases or increases.
T O O RI GIN A TE AN IN TERN AL CALL ◆ Lift handset or press Speaker key . ◆ Receive dial tone. ◆ Dial desired station number . ◆ Use handset or MIC to converse. OUTSIDE LINE APPEARANCE T O ORIGINA TE ◆ Press the OUTSIDE LINE APPEARANCE feature key .
10 ◆ Enter desired station number , feature code or outside access code and telephone number . Display indicates digits dialed. ◆ Press Feature again to save the number . T O V ERIFY ◆ Press Feature button. ◆ Press desired One Touch button. ◆ Display indicates digits programmed.
11 T O O RI GIN A TE A CALL USIN G S PEED CALLIN G (INDI VID UAL / GR O UP) ◆ Press the Redial button. ◆ Enter via dial pad the desired speed calling number (00-99). NOTE: Access to feature is based on data assignment. AUTOMA TIC IDLE RETURN ◆ Press Speaker key .
F O R C E D ACCO UNT C ODE ◆ Lift handset or press Speaker , receive dial tone. ◆ Enter feature access code, receive service set tone. ◆ Enter Forced Account Code (up to 10 digits), receive dial tone. A UT HO RIZA TI O N C ODE T O E NTER W ITHOUT A CCOUNT C ODE ◆ Lift handset or press Speaker , receive dial tone.
13 VOICE FIRST/TONE FIRST Allows incoming station calls to your Dterm to either ring or go to voice announcement. ◆ Press Speaker . Receive dial tone. ◆ Dial V oice/T one access code, LCD display shows current mode receives feature dial tone. ◆ Press * , LCD display shows mode change, receive feature set tone.
A UT OMA TI C INTER C OM NOTE: Access to feature is based on data assignment. T O I NITIA TE ◆ Lift handset or press Speaker key . ◆ Press AICM key . ◆ T one burst is sent. T O A NSWER ◆ AICM key flashes green indicating an incoming intercom call.
◆ If called station is engaged in a non-intercom call, the station may press MICM after placing original caller on hold (with Hold key). DIAL INTERCOM T O INITIA TE ◆ Lift handset or press Speaker key . ◆ Press DICM key . ◆ Dial desired intercom station number (0-9).
T O ANSWER ◆ DICM LED flashes, indicating an incoming intercom call. T one burst or ring tone is heard. ◆ Press DICM . ◆ Lift handset or press Speaker . LCD shows solid green. DIAL BY NAME USING SYSTEM SPEED DIALING T O INITIA TE ◆ Press the SYS Soft Key .
17 DIAL BY NAME USING ST A TION SPEED DIALING T O INITIA TE ◆ Press the DIRECTORY key . ◆ Enter up to the first four characters of a name using the keypad. ◆ Press the ▲ or ▼ k ey to start the search. ◆ The name and the number are shown on the LCD.
NOTE: When entering an outside number you must include the Trunk Access Code (i.e., 9) followed by area code and number. TO PLACE A CALL ON HOLD ◆ Press Hold . Held line wink flashes. NOTE: If held line appears on other Dterm stations, the associated LED flashes red slowly.
T O PLA C E A CALL ON EX CLUS IVE H O LD ◆ Press Hold twice. Line appearance indi cates interrupted wink. NOTE: If held line appears on other Dterm stations, LED remains steadily lit red. T O R ETRIEVE ◆ Lift handset or press Speaker . ◆ Press held line.
TO PLACE A CALL ON REMOTE HOLD T O INITIA TE While in conversation with Station/T runk Party: ◆ Press the TRANSFER key . Receive interrupted dial tone. ◆ Dial destination station’ s extension. ◆ Receive ring back tone. ◆ Press the Hold key .
21 T O TRANSFE R A CALL ◆ After conversing, ask party to hold. ◆ Press Transfer key . Receive interrupted dial tone. ◆ Dial destination st ation’ s extension, hang up or wait for answer . 200 1 XFR (Time Display) Transferred station or trunk number (Time Display) CO N F E R E NC E ◆ W ith call in progress, ask party to hold.
CALL BACK (ST A TION) ◆ Lift handset or press Speaker . ◆ Dial desired station number and receive busy tone or ring back tone. ◆ Press Call Back or dial 2 and receive service set tone.
TO ANSWER A CAMPED-ON CALL ◆ While engaged in a call, receive the camp-on indication (one short tone burst). Answer LED flashes. ◆ Press Answer . Call in progress is placed on hold. ◆ Connection to camped-on call is established. ◆ Press Answer to return to original call.
T O ANSWER CALL W AITING (S T A TION 2000) ◆ Hear burst of tone. LCD display indicates CW and Answer button flashes. ◆ 2000 presses Answer button and converses with station 2001. NOTE: Station 2000 can alternate between the two parties by pressing Answer button.
CALL P ARK (SYSTEM) T O P ARK A C ALL F ROM T ERMINAL W ITH LCD ◆ While connected to a station or trunk, press Transfer and dial the Call Park access code, or press Call Park key .
CALL PICKUP (DIRECT) ◆ Lift handset. ◆ Press Call Pickup Direct . Lift handset. Key or dial Call Pickup Direct access code (may be stored on one-touch key). ◆ Dial extension number to be picked up. ◆ Connection to calling party is established.
◆ Press Speaker or lift handset. Dial tone is heard. Dial desired number . (No outgoing access code needed.) TIMED QUEUING (OUTSIDE LINE ONL Y) ◆ Press Speaker , receive dial tone. ◆ Dial Outside Line access code and desired number . ◆ Receive busy tone or ring no answer from distant end.
CID CALL BACK T O SEARCH , CALL BACK OR ERASE A C ALLING N UMBER USING S OFT K EYS ◆ Lift the handset or press Speaker key . ◆ Press MESSAGE key . ◆ Press Search Soft Key to search for desired number . ◆ Press CB Soft Key to call back desired number .
29 T O SEARCH , CALL BACK OR ERASE A C ALLING N UMBER WITHOUT USING S OFT K EYS ◆ Lift the handset or press Speaker key . ◆ Press MESSAGE key . ◆ Dial 1 to search for desired number . ◆ Dial 2 to call back desired number . ◆ Dial 3 to erase desired number .
30 T O CANCEL ◆ Press Speaker . Receive dial tone. ◆ Press FD-A plus * or dial Call Forwarding cancel code. Receive service set tone. LED goes out at your station (or the Dterm of the sub line station). ◆ Press Speaker . CNCL (Time Display) T O VERIFY ( WITH 16 OR 32- BUTTON D TERM ) ◆ Press Speaker .
31 CALL FOR W ARDING – BUSY T O SET ◆ Press Speaker . Receive dial tone. ◆ Press FD-B or dial Call Forwarding – Busy access code. Receive special dial tone. ◆ Dial destination station or external telephone number . Receive service set tone. ◆ FD-B LED lights (at your station or at the Dterm of the sub line station you are setting).
CALL FOR W ARDING – NO ANSWER T O SET ◆ Press Speaker . Receive dial tone. ◆ Press FD-N or dial Call Forwarding – No Answer access code. Receive special dial tone. ◆ Dial destination station or external telephone number . Receive service set tone.
33 CALL FOR W ARDING – DESTINA TION T O SET ◆ Press Speaker . Receive dial tone. ◆ Press FD-DS or dial Call Forwarding – Destination access code. Receive special dial tone. ◆ Dial station number to be forwarded to this line. W ait for service set tone.
TO SA VE AND REPEA T A NUMBER T OS A V E ◆ Press Speaker . ◆ Dial desired telephone number . ◆ Press S & R . Dialed number is now stored. S & R LED lights. T O REPEA T ◆ Press Speaker . ◆ Press S & R. Dterm automatically redials the programmed number .
BOSS/SECRET AR Y CALLING S ECRET ARY ◆ Lift handset, press boss’ ringing line. Ask calling party to hold. ◆ Press boss’ line again. V oice Call is automatically established. ◆ Announce the call to the boss. I F BOSS ACCEPTS CALL ◆ Secretary replaces handset.
I F BOSS REFUSES CALL ◆ Secretary presses Transfer key to return to calling party . NOTE: Access to feature is based on data assignment. BOSS/SECRET AR Y OVERRIDE Example: Station 2000 is boss, Station 2001 is secretary . Boss is connected to 2003. Incoming call on Outside line connects to secretary , but is intended for boss.
B OSS ◆ Hears burst of tone, Answer key flashes. LCD display indicates: Option 1 ◆ Boss presses Answer and converses with secretary . Outside line is placed on hold. ◆ Secretary hangs up. Boss is connected to Outside line. ◆ Boss can alternate between the two parties by pressing Answer .
TIMED REMINDER Example: Station 2000 wants to be reminded of a 9:00 a.m. meeting. T O SET ◆ Press Speaker . ◆ Press Timed Reminder key or dial T imed Reminder access code. ◆ Dial the desired reminder time in military format, receive set tone. At 9:00 a.
PRIV ACY RELEASE Example: Dterm Station B is engaged in a conversation, and allows Dterm Station A to enter the call in progress. ◆ Station 2000, while engaged in conversation, presses Conf key . Conf key flashes. ◆ Station 2001 lifts handset or presses Speaker .
40 D IAL M ESSAGE 0 IN:BACK HH:MM 1 OUT:BACK HH:MM 2 AWAY:BACK MM:DD 3 VACATION MM:DD ◆ If 0 or 1: dial desired military time. ◆ If 2 or 3: dial month and day . Example: June 24=0624. ◆ Receive dial tone. ◆ Press Speaker . 0900 AWAY:BACK (Time Display) 0900 IN:BACK (Time Display) T O CANCEL ◆ Press Speaker.
41 ◆ When the desired letter is displayed, depression of the Transfer key will change the letter to a lower case letter (default is upper case). Depress the Hold key to enter that letter and advance to the next entry . ◆ Repeat the previous two steps until the desired name is displayed and entered.
O UTSIDE L INE 9 Q UEUING -O UTSIDE L INE S ET * 1 C ALL B ACK S ET C ANCEL # 1 C ALL F ORWARDING –A LL C ALLS E NTRY * 5 C ANCEL # 5 C ALL F ORWARDING –N O A NSWER /E NTRY * 6 B USY L INE C ANCEL.
43 NOTES NEC-403 DtermSeries i UG Insid6 1/23/03 12:31 PM Page 43.
NEC-403 DtermSeries i UG Insid6 1/23/03 12:31 PM Page 44.
MIC (Microphone) Lamp DIRECTOR Y MESSAGE RECALL FEA TURE CONF (Conference) REDIAL HOLD TRANSFER UP / DOWN ( ) ANSWER SPEAKER P ROGRAMMABLE K EYS One-T ouch Speed Dial / Feature Keys (Programmable by u.
NEC America, Inc. Corporate Networks Group 6555 N. State Highway 161 Irving Texas 75039 Visit our Web site at www.cng.nec.com ©NEC America, Inc. 2002 NEAX and Dterm are registered trademarks of NEC Corporation.
Ein wichtiger Punkt beim Kauf des Geräts NEC NEAX2000IPS (oder sogar vor seinem Kauf) ist das durchlesen seiner Bedienungsanleitung. Dies sollten wir wegen ein paar einfacher Gründe machen:
Wenn Sie NEC NEAX2000IPS noch nicht gekauft haben, ist jetzt ein guter Moment, um sich mit den grundliegenden Daten des Produkts bekannt zu machen. Schauen Sie zuerst die ersten Seiten der Anleitung durch, die Sie oben finden. Dort finden Sie die wichtigsten technischen Daten für NEC NEAX2000IPS - auf diese Weise prüfen Sie, ob das Gerät Ihren Wünschen entspricht. Wenn Sie tiefer in die Benutzeranleitung von NEC NEAX2000IPS reinschauen, lernen Sie alle zugänglichen Produktfunktionen kennen, sowie erhalten Informationen über die Nutzung. Die Informationen, die Sie über NEC NEAX2000IPS erhalten, werden Ihnen bestimmt bei der Kaufentscheidung helfen.
Wenn Sie aber schon NEC NEAX2000IPS besitzen, und noch keine Gelegenheit dazu hatten, die Bedienungsanleitung zu lesen, sollten Sie es aufgrund der oben beschriebenen Gründe machen. Sie erfahren dann, ob Sie die zugänglichen Funktionen richtig genutzt haben, aber auch, ob Sie keine Fehler begangen haben, die den Nutzungszeitraum von NEC NEAX2000IPS verkürzen könnten.
Jedoch ist die eine der wichtigsten Rollen, die eine Bedienungsanleitung für den Nutzer spielt, die Hilfe bei der Lösung von Problemen mit NEC NEAX2000IPS. Sie finden dort fast immer Troubleshooting, also die am häufigsten auftauchenden Störungen und Mängel bei NEC NEAX2000IPS gemeinsam mit Hinweisen bezüglich der Arten ihrer Lösung. Sogar wenn es Ihnen nicht gelingen sollte das Problem alleine zu bewältigen, die Anleitung zeigt Ihnen die weitere Vorgehensweise – den Kontakt zur Kundenberatung oder dem naheliegenden Service.
