Benutzeranleitung / Produktwartung 321827C-01 des Produzenten National Instruments
Zur Seite of 59
Serial Getting Started with Your PCMCIA Serial Hardware and Software for Windows Me/9 x PCMCIA Serial for Wind ows Me/9x September 2000 Edition Part Number 3218 27C-01.
Support Worldwide Technical Support and Product Info rmation ni.com National Instruments Corporate Headquarters 11500 North Mopac Expressway Austin, Texas 78759-3504 USA Tel: 512 794 0100 Worldwide Of.
Important Information Warranty The serial hardware is warranted against defects in materials and workmanship for a period of one year from the date of shipmen t, as evidenced by receipts or othe r documentation. National Instruments will , at its option, repair or replace equipment that pro ves to be defective during the warranty period.
Compliance FCC/Canada Radio Frequency Interference Compliance* Determining FCC Class The Federal Communications Commission (FCC) has rules to protect wireless communications from interference.
• Connect the equipment into an outlet on a circuit different f rom that to which the receiver is connected. • Consult the dealer or an experienced radio/T V technician for help. Canadian Departmen t of Communications This Class B digital apparatus meets all requirements of the Canadian Interference-Causing Equipment Regulations.
© National Instruments Corporation vii PCMCIA Serial for Windows Me/9x Contents About This Manual Conventions ............ ........... .............. .............. ............ .............. ........... .............. ............. x i Related Documentation .
Contents PCMCIA Serial for Windows Me/9x viii ni.com Advanced Port Settings ............ ........... .............. ............... .............. ........... ...... 3-3 Transceiver Mode ................. ............ .............. .............. ...
Contents © National Instruments Corporation ix PCMCIA Serial for Windows Me/9x Figures Figure 2-1. Add/Remove Programs Properties Dialog Box..................... .............. .. 2-1 Figure 2-2. NI-Serial Setup Screen ................ ..............
© National Instruments Corporation xi PCMCIA Serial for Windows Me/9x About This Manual This manual contains instructions to help you inst all and configure the National Instruments serial hardware and the NI-Serial software for W indo ws Me/9 x .
About This Manual PCMCIA Serial for Windows Me/9x xii ni.com Related Documentation The following documents contain information that you might find helpful as you read this manual: • ANSI/EIA-232-D S.
© National Instruments Corporation 1-1 PCMCIA Serial for Windows Me/9x 1 Introduction This chapter explains ho w to use this manual, lists what you need to get started and optional equip ment you can order , and briefly describes the serial hardware and the NI-Serial soft ware.
Chapter 1 Introduction PCMCIA Serial for Windows Me/9x 1-2 ni.com What Y ou Need to Get Started Before you install your serial hardware and the NI-Serial software, make sure you have all of the follow.
Chapter 1 Introduction © National Instruments Corporation 1-3 PCMCIA Serial for Windows Me/9x The PCMCIA-485 interfaces support four hardware transcei ver c ontrol modes for reliable communicatio n with two-wire and four-wire de vices. Refer to Chapter 4, Using Your Serial Hardware , for more information about transceiv er control modes.
Chapter 1 Introduction PCMCIA Serial for Windows Me/9x 1-4 ni.com T ime-Saving Development T ools Your kit includes the NI-Serial software for Windows M e/9 x .
© National Instruments Corporation 2-1 PCMCIA Serial for Windows Me/9x 2 Installation and V erification This chapter describes how to install the NI-Serial software, serial hardware, and cables, and how to v erify the installati on. Install the Software Install the NI-Seri al software for Win dows Me/9 x before y ou install the hardware: 1.
Chapter 2 Installation and Verification PCMCIA Serial for Windows Me/9x 2-2 ni.com 3. Click on the Install button. 4. When prompted, insert the NI-Serial Software for Windows 2000/NT/Me/9x CD and click on the Next b utton to proceed. The software installa tion wizard be gins with the screen sho wn in Figure 2-2.
Chapter 2 Insta llation and Verification © National Instruments Corporation 2-3 PCMCIA Serial for Windows Me/9x Install the Hardware To install the PCMCIA-232 or PCMCIA-485 in your computer, first start Windows Me /9 x .
Chapter 2 Installation and Verification PCMCIA Serial for Windows Me/9x 2-4 ni.com V erify the Installation When you begin to verify the installatio n, keep in mind that the serial ports built into the computer are typically named from COM1 to COM4.
Chapter 2 Insta llation and Verification © National Instruments Corporation 2-5 PCMCIA Serial for Windows Me/9x Figure 2-4. Device Manager Ports List for PCMCIA Serial Card Correctly Installed.
Chapter 2 Installation and Verification PCMCIA Serial for Windows Me/9x 2-6 ni.com Figure 2-5. Device Man ager Ports List for PCMCIA Serial Card Incorrectly Installed V erify the Hardware Resources For every port of the newly installed serial interface, double-click on the name of the serial port in the Device Manager.
Chapter 2 Insta llation and Verification © National Instruments Corporation 2-7 PCMCIA Serial for Windows Me/9x Determine Which Physical Port Is Associated with COMx For every port of the newly installed serial interface, double-click on the name of the serial port in the Device Manager.
Chapter 2 Installation and Verification PCMCIA Serial for Windows Me/9x 2-8 ni.com Connect the Cables For the PCMCIA serial cards, you can use the standard DB-9 connector found on most serial cables. Figure 2-6 and T able 2-1 giv e the pin lo cations and d escriptions of the DB-9 connector , which is found on the PCMCIA serial cable.
Chapter 2 Insta llation and Verification © National Instruments Corporation 2-9 PCMCIA Serial for Windows Me/9x Connecting T wo-Wire Devices The PCMCIA-485 boards are designed to work with either two- or four-wire devices. If you are using a two-wire device, refer to the device documentation for specifi c wiring instructions.
© National Instruments Corporation 3-1 PCMCIA Serial for Windows Me/9x 3 Configuration This chapter describes how to vie w or change the communication po rt settings. View or Change Communication Port Settings The serial config uration util ity is fully i ntegrated with t he Windows Me/9 x Device Manager.
Chapter 3 Configuration PCMCIA Serial for Windows Me/9x 3-2 ni.com After you ha ve selected the serial port parameters for the current port, click on the OK b utton to sav e the changes or click on the Cancel butto n to exit the dialog box without saving changes.
Chapter 3 Configuration © National Instruments Corporation 3-3 PCMCIA Serial for Windows Me/9x Bits per Second Bits per second , or baud rate, is the speed for a serial port. Data Bits Data bits is the number of data bits in a single serial byte. Parity Parity is the specification for even, odd, or no parity bits in each transmitted byte.
Chapter 3 Configuration PCMCIA Serial for Windows Me/9x 3-4 ni.com The following sections describe the adv anced settings opti ons. T ransceiver Mode This field shows the transceiver mode in use, and applies only to PCMCIA-485 boards. F or more information about tr ansceiver modes, r e f e rt o C h a p t e r4 , Using Your Serial Hardware .
© National Instruments Corporation 4-1 PCMCIA Serial for Windows Me/9x 4 Using Y our Serial Hardware This chapter describes how to set the hardw are transcei ver control mode for your RS-485 interfaces and lists some general programming requ irements.
Chapter 4 U sing Y our Seria l Hardware PCMCIA Serial for Windows Me/9x 4-2 ni.com Note Signal names with an ov erscore, such as DTR , indicate that the signal is activ e low . Four -Wire Mode Use the four-wire mode for most full-duplex systems. In th is mode, the transmitter and receiver are always enabled.
Chapter 4 Using Y our Serial Hardware © National Instruments Corporation 4-3 PCMCIA Serial for Windows Me/9x T wo-Wire Mode: TXRDY Auto Control In this mode, the serial hardware transparently enables the transmitter and receiver in a two-wire system.
Chapter 4 U sing Y our Seria l Hardware PCMCIA Serial for Windows Me/9x 4-4 ni.com The scratch register is located at offset 7 from the base address of the port. For e xample, if COM2 were located at base address 0x3F8, and you wanted to set the PCMCIA-485 board to two-w ire mode with DTR control, you would write a 0x02 to I/O address 0x3FF .
© National Instruments Corporation A-1 PCMCIA Serial for Windows Me/9x A Serial Port Information This appendix describes the RS-232, RS-422, and RS-485 standards and explains some of the issues in volv ed with these types of serial communication. T able A-1 lists the features of the RS-232, RS-422, and RS-485 standards.
Appendix A Serial Port Information PCMCIA Serial for Windows Me/9x A-2 ni.com distances of 50 ft and with data rates up to 20 kbytes/s. Ho we ver , because of improv ements in line dri vers and cabling, you can usually increase the actual performance of the b us past the limitations on speed and distance recommended in the specification.
Appendix A Serial Port Information © National Instruments Corporation A-3 PCMCIA Serial for Windows Me/9x Serial Communication Issues This section explains some serial communication issues, incl uding duplex architectures, termination methods, bias resistors, and types of connecting equipment.
Appendix A Serial Port Information PCMCIA Serial for Windows Me/9x A-4 ni.com Figure A-1. T ypica l Full-Duplex System Half Duplex A typical half-duplex multidrop bus architecture also in volv es a master-slav e protocol. Howe ver , in a half-duplex system, all transm itters and recei vers are connected to the same transmission line.
Appendix A Serial Port Information © National Instruments Corporation A-5 PCMCIA Serial for Windows Me/9x T erminati o n Because each dif ferential pair of wires is a transmission line, you must properly terminate the line to prev ent reflection s.
Appendix A Serial Port Information PCMCIA Serial for Windows Me/9x A-6 ni.com Figure A-4. Straight-Through Cabling in a DTE-to- DCE Inter face Straight-through cabling is still th e standard method to connect a modem to your PC.
© National Instruments Corporation B-1 PCMCIA Serial for Windows Me/9x B Uninstalling the Hardware and Software This appendix describes ho w to uninstall your serial hard ware and the NI-Serial software.
Appendix B Uninstalling the Hardware and Sof tware PCMCIA Serial for Windows Me/9x B-2 ni.com 5. Select the National Instruments port to remov e from the list of ports, as sho wn in Figure B-1. Figure B-1. Selecting an Inter face to Uninstal l 6. Click on the Remove button.
Appendix B Uninstalling the H ardware and Software © National Instruments Corporation B-3 PCMCIA Serial for Windows Me/9x Uninstall the Software Before uninstalling the software, remove all serial port information from the W indows Me/9 x Device Manager , as describe d in the pre vi ous section.
Appendix B Uninstalling the Hardware and Sof tware PCMCIA Serial for Windows Me/9x B-4 ni.com 3. Select the serial software you want to remov e, and click on the Add/Remove button. The uninstall program runs and removes all folders, programs, VxDs, DLLs, and re gistry entries associated with the NI-Serial software.
© National Instruments Corporation C-1 PCMCIA Serial for Windows Me/9x C T roubleshooting and Common Questions This appendix describes ho w to troubleshoot problems and answers some common questions.
Appendix C T roubleshooting and Co mmon Questions PCMCIA Serial for Windows Me/9x C-2 ni.com Selecting Conflict-Free Resources When the Device Manager i ndicates a conflict with another device, you can usually correct the problem by manually selecting conflict-free resources.
Appendix C T roubleshooting and Common Questions © National Instruments Corporation C-3 PCMCIA Serial for Windows Me/9x • If the utility reports fe wer ports installed than it shoul d, refer to Chapter 2, Installation and Verification , and follow these troubleshooting steps: 1.
Appendix C T roubleshooting and Co mmon Questions PCMCIA Serial for Windows Me/9x C-4 ni.com 4. Click on the View devices by type button. 5. Double-click on the Ports (COM & LPT) icon to display a list of all ports that W indows recognizes.
Appendix C T roubleshooting and Common Questions © National Instruments Corporation C-5 PCMCIA Serial for Windows Me/9x Common Questions How can I determine which type of serial hardwar e I hav e installed? 1. Select Start » Settings » Control Panel and double-click on the System icon.
Appendix C T roubleshooting and Co mmon Questions PCMCIA Serial for Windows Me/9x C-6 ni.com In most cases, W indows Me/9 x does not assign names COM1 through COM4 to the serial hardware.
Appendix C T roubleshooting and Common Questions © National Instruments Corporation C-7 PCMCIA Serial for Windows Me/9x Figure C-2. Multi-Function Ada pter Class in the Device Manager How do I r emov.
© National Instruments Corporation D-1 PCMCIA Serial for Windows Me/9x D Specifications This appendix describes the characteristics of the serial hardware, the NI-Serial software, along with th e recommended operating conditions. Hardware Specifications Table D-1.
Appendix D Specifications PCMCIA Serial for Windows Me/9x D-2 ni.com Software Specifications Table D-2. Environmental Characteristics of the Serial Hardware Characteristic Specif ication Operating En .
© National Instruments Corporation E-1 PCMCIA Serial for Windows Me/9x E T echnical Support Resources W eb Support National Instruments W eb support is your first stop for help in solving installation, configuration, and application pro blems and questions.
Appendix E T echnic al Support Resources PCMCIA Serial for Windows Me/9x E-2 ni.com W orldwide Support National Instruments has of fices located around the world to help address your support needs. Y ou can access our branch off ice W eb sites from the W o rldwide Of fices section of ni .
© National Instruments Corporation G-1 PCMCIA Serial for Windows Me/9x Glossar y Pref ix Meaning V alue p- pico- 10 – 12 n- nano- 10 – 9 µ- micro- 10 – 6 m- milli- 10 – 3 k- kilo- 10 3 M- me.
Glossary PCMCIA Serial for Windows Me/9x G-2 ni.com DCD data carrier detect DCE data communications equipment or data circuit-terminating equipment DLL dynamic link li brary DMA direct memory access D.
Glossary © National Instruments Corporation G-3 PCMCIA Serial for Windows Me/9x MB megab ytes of memory PC personal computer PCI Peripheral Components Interconnect RAM random-access memory RI ring in.
© National Instruments Corporation I-1 PCMCIA Serial for Windows Me/9x Index A add/remove programs properties dialog box (figure), 2-1, B-3 advanced port setting s, 3-3 dialog box (figure), 3-3 trans.
Index PCMCIA Serial for Windows Me/9x I-2 ni.com DOS-based addresses (table), C-5 DTE vs. DCE, A-5 DTE-to-DCE interface, A-6 straight-through cabling in (figure), A-6 DTE-to-DTE interface, A-6 null-mo.
Index © National Instruments Corporation I-3 PCMCIA Serial for Windows Me/9x NI-Serial setup screen (figure), 2-2 null-modem cabling in a DTE-to-DTE interface (figure), A-6 O optional equipment, 1-2 .
Index PCMCIA Serial for Windows Me/9x I-4 ni.com successful uninstallation (figure), B-4 uninstalling, B-3 setting transceiver contro l mode, 4-3 setting with DeviceloControl, 4-4 setup screen for NI-.
Ein wichtiger Punkt beim Kauf des Geräts National Instruments 321827C-01 (oder sogar vor seinem Kauf) ist das durchlesen seiner Bedienungsanleitung. Dies sollten wir wegen ein paar einfacher Gründe machen:
Wenn Sie National Instruments 321827C-01 noch nicht gekauft haben, ist jetzt ein guter Moment, um sich mit den grundliegenden Daten des Produkts bekannt zu machen. Schauen Sie zuerst die ersten Seiten der Anleitung durch, die Sie oben finden. Dort finden Sie die wichtigsten technischen Daten für National Instruments 321827C-01 - auf diese Weise prüfen Sie, ob das Gerät Ihren Wünschen entspricht. Wenn Sie tiefer in die Benutzeranleitung von National Instruments 321827C-01 reinschauen, lernen Sie alle zugänglichen Produktfunktionen kennen, sowie erhalten Informationen über die Nutzung. Die Informationen, die Sie über National Instruments 321827C-01 erhalten, werden Ihnen bestimmt bei der Kaufentscheidung helfen.
Wenn Sie aber schon National Instruments 321827C-01 besitzen, und noch keine Gelegenheit dazu hatten, die Bedienungsanleitung zu lesen, sollten Sie es aufgrund der oben beschriebenen Gründe machen. Sie erfahren dann, ob Sie die zugänglichen Funktionen richtig genutzt haben, aber auch, ob Sie keine Fehler begangen haben, die den Nutzungszeitraum von National Instruments 321827C-01 verkürzen könnten.
Jedoch ist die eine der wichtigsten Rollen, die eine Bedienungsanleitung für den Nutzer spielt, die Hilfe bei der Lösung von Problemen mit National Instruments 321827C-01. Sie finden dort fast immer Troubleshooting, also die am häufigsten auftauchenden Störungen und Mängel bei National Instruments 321827C-01 gemeinsam mit Hinweisen bezüglich der Arten ihrer Lösung. Sogar wenn es Ihnen nicht gelingen sollte das Problem alleine zu bewältigen, die Anleitung zeigt Ihnen die weitere Vorgehensweise – den Kontakt zur Kundenberatung oder dem naheliegenden Service.
