Benutzeranleitung / Produktwartung R50p des Produzenten Lenovo
Zur Seite of 232
ThinkPad Computer Hardware Maintenance Manual Jul y 2005 This manual supports: ThinkP ad R50/R50p, R51 series ThinkP ad Dock II (MT 2877) (MT 1829, 1830, 1831, 1832, 1833, 2889, 2894, 2895) 1836, 1840.
Note Before using this information and the product it supports, be sure to read the general information under “Notices” on page 224. First Edition (July 2005) © Copyright Lenovo 2005. Portions © Copyright International Business Machines Corporation 2005.
Contents About this manual . . . . . . . . . . .1 Introduction . . . . . . . . . . . . .3 Important service information . . . . . . . . .3 Strategy for replacing FRUs . . . . . . . .3 How to use error messages . . . . . . . .4 Diskette compatibility matrix .
1030 Hard disk drive . . . . . . . . . .6 9 1040 DIMM (optional) . . . . . . . . .7 1 1050 Keyboard . . . . . . . . . . .7 2 1060 DIMM (standard) . . . . . . . . .7 6 1070 Modem daughter card (MDC/MDC-2) . . .7 7 1080 Bluetooth/Modem daughter card (BMDC/BMDC-2) .
About this manual This manual contains service and reference information for ThinkPad ® R50/R50p and R51 series (MT1829, 1830, 1831, 1832, 1833, 1836, 1840, 1841, 2883, 2887, 2888, 2889, 2894, 2895), and ThinkPad Dock II (MT2877) products. Use this manual along with the advanced diagnostic tests to troubleshoot problems.
2 R50/R50p, R51 Series.
Introduction Important service information Important BIOS and device driver fixes are customer-installable. The BIOS and device drivers are posted on the customer support site http://www.
Strategy for replacing a hard disk drive Always try to run a low-level format before replacing a hard disk drive. Attention: The drive startup sequence in the computer you are servicing may have been changed. Be extremely careful during write operations such as copying, saving, or formatting.
Safety notice 1 Before the computer is powered on after FRU replacement, make sure all screws, springs, and other small parts are in place and are not left loose inside the computer . V erify this by shaking the computer and listening for rattling sounds.
Safety notice 2 DANGER Some standby batteries contain a small amount of nickel and cadmium. Do not disassemble a standby battery , recharge it, throw it into fire or water , or short-circuit it. Dispose of the battery as required by local ordinances or regulations.
(continuation of safety notice 2) Alcune batterie di riserva contengono una piccola quantità di nichel e cadmio. Non smontarle, ricaricarle, gettarle nel fuoco o nell’acqua né cortocircuitarle. Smaltirle secondo la normativa in vigore (DPR 915/82, successive disposizioni e disposizioni locali).
Safety notice 3 DANGER The battery pack contains small amounts of nickel. Do not disassemble it, throw it into fire or water , or short-circuit it. Dispose of the battery pack as required by local ordinances or regulations. Use only the battery in the appropriate parts listing when replacing the battery pack.
(continuation of safety notice 3) La batteria contiene piccole quantità di nichel. Non smontarla, gettarla nel fuoco o nell’acqua né cortocircuitarla. Smaltirla secondo la normativa in vigore (DPR 915/82, successive disposizioni e disposizioni locali).
Safety notice 4 DANGER The lithium battery can cause a fire, an explosion, or a severe burn. Do not recharge it, remove its polarized connector , disassemble it, heat it above 100°C (212°F), incinerate it, or expose its cell contents to water . Dispose of the battery as required by local ordinances or regulations.
(continuation of safety notice 4) La batteria di supporto e una batteria al litio e puo incendiarsi, esplodere o procurare gravi ustioni. Evitare di ricaricarla, smontarne il connettore polarizzato, smontarla, riscaldarla ad una temperatura superiore ai 100 gradi centigradi, incendiarla o gettarla in acqua.
Safety notice 5 If the LCD breaks and the fluid from inside the LCD gets into your eyes or on your hands, immediately wash the affected areas with water for at least 15 minutes. Seek medical care if any symptoms from the fluid are present after washing.
Safety notice 6 DANGER To avoid shock, do not remove the plastic cover that protects the lower part of the inverter card. Afin d’éviter tout risque de choc électrique, ne retirez pas le cache en plastique protégeant la partie inférieure de la carte d’alimentation.
Safety notice 7 DANGER Though the main batteries have low voltage, a shorted or grounded battery can produce enough current to burn personnel or combustible materials.
Safety notice 8 DANGER Before removing any FRU, power off the computer , unplug all power cords from electrical outlets, remove the battery pack, and then disconnect any interconnecting cables.
Safety information The following section presents safety information with which you need to be familiar before you service a ThinkPad computer . General safety Follow these rules to ensure general safety: v Observe good housekeeping in the area of the machines during and after maintenance.
v After service, reinstall all safety shields, guards, labels, and ground wires. Replace any safety device that is worn or defective. v Reinstall all covers correctly before returning the machine to the customer . v Fan louvers on the machine help to prevent overheating of internal components.
– Ensure that another person, familiar with the power-off controls, is near you. Attention: Another person must be there to switch off the power , if necessary . – Use only one hand when working with powered-on electrical equipment; keep the other hand in your pocket or behind your back.
Safety inspection guide The purpose of this inspection guide is to assist you in identifying potentially unsafe conditions. As each machine was designed and built, required safety items were installed to protect users and service personnel from injury .
8. Check that the power-supply cover fasteners (screws or rivets) have not been removed or tampered with. Handling devices that are sensitive to electrostatic discharge Any computer part containing transistors or integrated circuits (ICs) should be considered sensitive to electrostatic discharge (ESD.
– Use the round ground prong of the ac plug on ac-operated computers. Grounding requirements Electrical grounding of the computer is required for operator safety and correct system function. Proper grounding of the electrical outlet can be verified by a certified electrician.
Laser compliance statement Some models of ThinkPad computer are equipped from the factory with an optical storage device such as a CD-ROM drive or a DVD-ROM drive. Such devices are also sold separately as options. If one of these drives is installed, it is certified in the U.
If a CD-ROM drive, a DVD-ROM drive, or another laser device is installed, note the following: CAUTION: Opening the CD-ROM drive, the DVD-ROM drive, or any other optical storage device could result in exposure to hazardous laser radiation. There are no serviceable parts inside those drives.
A CD-ROM drive, a DVD-ROM drive, or any other storage device installed may contain an embedded Class 3A or Class 3B laser diode. Note the following: DANGER Emits visible and invisible laser radiation when open. Do not stare into the beam, do not view directly with optical instruments, and avoid direct exposure to the beam.
General descriptions The desciptions in this chapter apply to any ThinkPad model that has the PC-Doctor ® for DOS diagnostics program. Some descriptions might not apply to your particular computer . Read this first Before you go to the checkout guide, be sure to read this section.
__ 2. Date of service __ 3. Date on which the machine failed __ 4. Date of purchase __ 5. Failure symptoms, error codes appearing on the display , and beep symptoms __ 6. Procedure index and page number in which the failing FRU was detected __ 7. Failing FRU name and part number __ 8.
Related service information This section provides information about the following: v “Service Web site” v “Restoring the pre-installed system” v “Passwords” on page 28 v “Power managemen.
5. If you get a message asking which operating system to install, select the proper operating system and press Enter . 6. A message is displayed: “ Full Recovery: ”. Press Enter to select. 7. On each of the next three windows, press the Y key . 8.
information stored in the BIOS Setup Utility . The user must enter the SVP in order to get access to the BIOS Setup Utility and change the system configuration. Attention: If the SVP has been forgotten and cannot be made available to the servicer , there is no service procedure to reset the password.
message is displayed at the lower-left of the screen, press the Access IBM button. The Rescue and Recovery screen opens. For models supporting the Passphrase function, press F1 while POP icon is appearing on the screen; then enter the POP . For the other models, enter the POP .
4. Select Security , using the cursor keys to move down the menu. 5. Select Password . 6. Select Hard-disk x password , where x is the letter of the hard disk drive. A pop-up window opens. 7. Select Master HDP . 8. Enter the master HDP; then leave the New Password field blank and press Enter twice.
Power management To reduce power consumption, the computer has three power management modes: screen blank, standby , and hibernation. Screen blank mode Screen blank mode has three variants, as follows: 1. If you press Fn+F3, or if the time set on the “LCD off timer” in BIOS Setup Utility expires, v The LCD backlight turns off.
v Open the LCD cover . v T urn on the power switch. Also, in either of the following events, the computer automatically returns from standby mode and resumes operation: v The ring indicator (RI) is signaled by a serial device or a PC Card device. v The time set on the resume timer elapses.
Checkout guide Use the following procedures as a guide in identifying and correcting problems with the ThinkPad computer . Note: The diagnostic tests are intended to test only ThinkPad products. The use of non-ThinkPad products, prototype cards, or modified options can lead to false indications of errors and invalid system responses.
3. Authenticating the digital signature takes about 15 seconds; then the ThinkPad computer will reboot into PC-DOS. 4. A batch file automatically starts up to prompt you through the process of creating diskettes. Yo u are notified of how many diskettes you will need.
The options on the test menu are as follows: Diagnostics Interactive T ests v Run Normal T est v Run Quick T est v CPU/Coprocessor v Systemboard v Video Adapter v Serial Ports v Parallel Ports v Fixed.
Detecting system information with PC-Doctor PC-Doctor can detect the following system information: Hardware Info v System Configuration v Memory Contents v Physical Disk Drives v Logical Disk Drives v.
Checking the ac adapter Yo u are here because the computer fails only when the ac adapter is used. v If the power problem occurs only when the port replicator is used, replace the port replicator . v If the power-on indicator does not turn on, check the power cord of the ac adapter for correct continuity and installation.
under this condition the battery pack can charge to 100% of its capacity . This protects the battery pack from being overcharged or from having a shortened life.
4. Remove the backup battery (see “Checking the battery pack” on page 38). 5. Measure the voltage of the backup battery . See the following figure. Red (+) Black (-) Wire V oltage (V dc) Red +2.5 to +3.2 Black Ground v If the voltage is correct, replace the system board.
ThinkPad R50/R50p and R51 Series Product overview . . . . . . . . . . . .4 3 Specifications . . . . . . . . . . . .4 3 Status indicators . . . . . . . . . . .4 8 FRU tests . . . . . . . . . . . . .5 0 Fn key combinations . . . . . . . . . .5 2 Symptom-to-FRU index .
Front view . . . . . . . . . . . . 136 Rear view . . . . . . . . . . . . . 138 Bottom view . . . . . . . . . . . . 139 Parts list . . . . . . . . . . . . . . 140 Overall . . . . . . . . . . . . . 140 LCD FRUs . . . . . . . . . . . . 188 14.1-in. XGA TFT .
Product overview This section presents the following product-unique information: v “Specifications” v “Status indicators” on page 48 v “FRU tests” on page 50 v “Fn key combinations” on.
Feature Description Standard memory R50 series: v 256 MB DDR SDRAM SO-DIMM (PC2700) card × 1 v 512 MB DDR SDRAM SO-DIMM (PC2700) card × 1 R50p series: v 512 MB DDR SDRAM SO-DIMM (PC2700) card × 1 v.
Feature Description I/O port v External monitor connector v Stereo headphone jack v Monaural microphone jack v Infrared port v Parallel connector v Docking connector v RJ1 1 connector v RJ45 connector v TV -out connector (S-Video) v Video-in connector v Universal serial bus (USB) 2.
Feature Description Ultrabay Enhanced device R50 series: v CD-ROM drive, 12.7 mm high v DVD drive, 12.7 mm high v DVD/CD-RW combo drive, 12.7 mm high v DVD-RW/CD-R W combo drive, 12.7 mm high (option) R50p series: v CD-ROM drive, 12.7 mm high v DVD/CD-RW combo drive, 12.
Feature Description Integrated wireless LAN feature v 802.1 1b v 802.1 1b/g v 802.1 1a/b/g and Bluetooth wireless Mini PCI adapter R50/ R50p series: v Intel PRO/Wireless LAN 2100 3B Mini PCI Adapter (802.1 1b) v ThinkPad 1 1a/b/g Wireless LAN Mini PCI Adapter (802.
Status indicators The system status indicators show the status of the computer , as follows: R 1 2 3 4 5 6 7 8 9 R 2 7 8 Product overview 48 R50/R50p, R51 Series.
Indicator Meaning 1 Wireless status Green: The wireless feature (the IEEE 802.1 1 standard) is on, and the radio link is ready for use. Blinking green: Data is being transmitted. 2 Bluetooth wireless status R Green: Bluetooth wireless feature is operational.
Indicator Meaning 8 Standby status Green: The computer is in standby mode. Blinking green: The computer is entering standby mode or hibernation mode, or is resuming normal operation. 9 Ultrabay Enhanced status Green: An Ultrabay Enhanced device is installed and in use.
FRU Applicable test PC Card slots 1. Diagnostics --> Systemboard --> PCMCIA 2. Insert a PC Card Wrap Plug into every PC Card slot, and run Diagnostics --> Systemboard --> PCMCIA External Loop Keyboard 1. Diagnostics --> Systemboard --> Keyboard 2.
Fn key combinations The following table shows the function of each combination of Fn with a function key . Key combination Description Fn+F1 Reserved. Fn+F2 Reserved. Fn+F3 T urn off the computer display , leaving the screen blank. To turn the computer display on again, press any key or press the T rackPoint pointing stick.
Key combination Description Fn+F8 If the image displayed on the computer is smaller than the physical display , switch the computer screen size between expanded mode and normal mode.
Symptom-to-FRU index The symptom-to-FRU index in this section lists symptoms and errors and their possible causes. The most likely cause is listed first, in boldface type. Note: Do the FRU replacement or other actions in the sequence shown in the column headed “FRU or action, in sequence.
Symptom or error FRU or action, in sequence 0185 Bad startup sequence settings. Enter BIOS Setup and load Setup defaults. 1. Run BIOS Setup Utility . Press F9, and Enter to load the default setting. Then save the current setting by pressing F10. 0187 EAIA data access error—The access to EEPROM is failed.
Symptom or error FRU or action, in sequence 0220 Monitor type error—Monitor type does not match the one specified in CMOS. Load Setup Defaults in BIOS Setup Utility . 0230 Shadow RAM error—Shadow RAM fails at offset nnnn. System board . 0231 System RAM error—System RAM fails at offset nnnn.
Symptom or error FRU or action, in sequence 1803 Unauthorized daughter card is plugged in—T urn off and remove the daughter card. 1. Remove the daughter card that you installed.
Error messages Symptom or error FRU or action, in sequence Device address conflict. 1. Load “Setup Defaults” in the BIOS Setup Utility . 2. Backup battery . 3. System board. Allocation error for device. 1. Load “Setup Defaults” in the BIOS Setup Utility .
Beep symptoms Symptom or error FRU or action, in sequence One beep and a blank, unreadable, or flashing LCD. 1. Reseat the LCD connector . 2. LCD assembly . 3. External CRT . 4. System board. One long and two short beeps, and a blank or unreadable LCD.
LCD-related symptoms Important The TFT LCD for the notebook computer contains many thin-film transistors (TFT s). The presence of a small number of dots that are missing, discolored, or always lighted is characteristic of TFT LCD technology , but excessive pixel problems can cause viewing concerns.
Intermittent problems Intermittent system hang problems can be due to a variety of causes that have nothing to do with a hardware defect, such as cosmic radiation, electrostatic discharge, or software errors. FRU replacement should be considered only when a problem recurs.
FRU replacement notices This section contains notices related to removing and replacing parts. Read this section carefully before replacing any FRU. Screw notices Loose screws can cause a reliability problem.
v Make sure that you use the correct screw . If you have a torque screwdriver , tighten all screws firmly to the torque shown in the table. Never use a screw that you removed.
Retaining the UUID The Universally Unique Identifier (UUID) is a 128-bit number uniquely assigned to your computer at production and stored in the EEPROM of your system board. The algorithm that generates the number is designed to provide unique IDs until the year A.
3. To write ECA information, select 1. Write ECA/rework number from EEPROM , and follow the instruction. 4. To write box build date, select 4. Write box build date from EEPROM , and follow the instruction on the screen.
Removing and replacing a FRU This section presents directions and drawings for use in removing and replacing a FRU. Be sure to observe the following general rules: 1. Do not try to service any computer unless you have been trained and certified. An untrained person runs the risk of damaging parts.
1010 Battery pack DANGER Holding the battery release lever in the unlocked position 1 , remove the battery pack 2 . 2 1 When installing: Install the battery pack along the slide rails on the left and right sides of the battery-pack slot. Then make sure that the battery latch is locked.
1020 Ultrabay Enhanced device Note Ultrabay Enhanced does not accept any of the following devices: v Ultrabay Plus devices v Ultrabay 2000 devices For devices compatible with the Ultrabay Enhanced, see “Optional FRUs” on page 221. When you release the switch in step 1 , the lever pops out.
1030 Hard disk drive Attention v Do not drop the hard disk drive or apply any physical shock to it. The hard disk drive is sensitive to physical shock. Improper handling can cause damage and permanent loss of data. v Before removing the drive, have the user make a backup copy of all the information on it if possible.
2 When installing: Make sure that the hard-disk connector is attached firmly . 3 3 4 Removing and replacing a FRU 70 R50/R50p, R51 Series.
1040 DIMM (optional) For access, remove this FRU: v “1010 Battery pack” on page 67 Note: Loosen the screw 1 , but do not remove it. 1 4 3 3 When installing: Insert the notched end of the DIMM into the socket. Press the DIMM firmly , and pivot it until it snaps into the place.
1050 Keyboard For access, remove this FRU: v “1010 Battery pack” on page 67 1 1a Screw 1a is only for the models with 14.1-in. LCD. Step Icon Screw (quantity) Color T orque 1 3 M2 × 12 mm, bind-head, nylon-coated (3) Black 0.245 Nm (2.
Press the part indicated by the arrow 2 in the direction of the arrow . This releases the latches of the keyboard from the frame, so that the front side of the keyboard pops out. 2 3 4 When installing: Make sure that the connector 4 is firmly attached.
When installing: 1. Attach the connector 1 . 1 2. Install the keyboard so that the keyboard edges are under the frame. 2 (continued) Removing and replacing a FRU 74 R50/R50p, R51 Series.
3. To make sure that the front edge of the keyboard is housed firmly , gently press the keys with your fingers and try to slide the keyboard towards you. 3 3 4. Make sure that all the projections on the front side of the keyboard b are firmly attached under the frame.
1060 DIMM (standard) For access, remove these FRUs in order: v “1010 Battery pack” on page 67 v “1050 Keyboard” on page 72 1 1 2 When installing: Insert the notched end of the DIMM into the socket. Press the DIMM firmly , and pivot it until it snaps into the place.
1070 Modem daughter card (MDC/MDC-2) For access, remove these FRUs in order: v “1010 Battery pack” on page 67 v “1050 Keyboard” on page 72 1 2 1 Step Screw (quantity) Color T orque 1 M2 × 12 mm, bind-head, nylon-coated (2) Black 0.245 Nm (2.
T urn the card over 3 , and detach the modem connector 4 . 3 4 When installing: Make sure that connector 4 and the connector on the underside of the card are firmly attached. Then place the cable to fit in the cable guide as in the figure.
1080 Bluetooth/Modem daughter card (BMDC/BMDC-2) For access, remove these FRUs in order: v “1010 Battery pack” on page 67 v “1050 Keyboard” on page 72 1 2 1 Step Screw (quantity) Color T orque 1 M2 × 12 mm, bind-head, nylon-coated (2) Black 0.
T urn the card over 3 , and detach the modem connector 4 . If the Bluetooth wireless antenna jack has a tab marked ″ BT ″ , unplug the jack by pulling the tab with your fingers.
1090 Keyboard bezel For access, remove these FRUs in order: v “1010 Battery pack” on page 67 v “1050 Keyboard” on page 72 2 2 1 1 1 2 2a 2 2 2 1 Screw 2a is only for the models with 15.0-in. LCD. Step Icon Screw (quantity) Color T orque 1 1 M2 × 3 mm, small-head, nylon-coated (3) Silver 0.
5 4 3 4 3 3 3 3 5 4 4 Step Icon Screw (quantity) Color T orque 3 3 M2 × 12 mm, bind-head, nylon-coated (3) Silver 0.245 Nm (2.5 kgfcm) 4 4 M2 × 12 mm, bind-head, nylon-coated (2) Silver 0.245 Nm (2.5 kgfcm) 5 5 M2 × 18.9 mm, special (1) Silver 0.
When installing: 1. Place the keybard bezel so that the three latches are fixed in palce 1 . 1 While inserting the three latches, align the top-left corner of the keyboard bezel as in figure a . a (continued) 2. Press the left edges 2 and the front edges 3 of the keyboard bezel until the latches are snapped.
3 3 2 2 3. Attach the touch pad connector 4 . 4 4. Secure the keyboard bezel from the underside of the computer with the screws. Removing and replacing a FRU 84 R50/R50p, R51 Series.
1 100 Mini PCI adapter For access, remove these FRUs in order: v “1010 Battery pack” on page 67 v “1030 Hard disk drive” on page 69 v “1050 Keyboard” on page 72 v “1090 Keyboard bezel”.
If the wireless antenna jacks have tabs marked ″ MAIN ″ or ″ AUX ″ , unplug the jacks by pulling the tabs with your fingers. If the antenna jacks do not have the tabs, unplug the jacks by usin.
When installing: Plug in the wireless antenna cable as follows: Intel PRO/Wireless LAN 2100 3B Mini PCI Adapter or Intel PRO Wireless 2200BG Mini-PCI Adapter In case of the antenna jacks have the tabs, plug the gray antenna cable with the tab marked MAIN into jack M , and the black antenna cable with the tab marked AUX into jack A .
ThinkPad 1 1a/b/g W ireless LAN Mini PCI Adapter , ThinkPad 1 1b/g W ireless LAN Mini PCI Adapter In case of the antenna jacks have the tabs, plug the gray antenna cable with the tab marked MAIN into jack MAIN , and the black antenna cable with the tab marked AUX into jack AUX .
111 0 Fan assembly For access, remove these FRUs in order: v “1010 Battery pack” on page 67 v “1030 Hard disk drive” on page 69 v “1050 Keyboard” on page 72 v “1090 Keyboard bezel” on page 81 3 1 2 Step Screw (quantity) Color T orque 1 M2 × 10 mm, flat-head, nylon-coated (3) Black 0.
1 120 CPU For access, remove these FRUs in order: v “1010 Battery pack” on page 67 v “1030 Hard disk drive” on page 69 v “1050 Keyboard” on page 72 v “1090 Keyboard bezel” on page 81 v.
1 130 Backup battery DANGER For access, remove these FRUs in order: v “1010 Battery pack” on page 67 v “1030 Hard disk drive” on page 69 v “1050 Keyboard” on page 72 v “1090 Keyboard bezel” on page 81 1 2 When installing: Make sure that the battery connector 2 is firmly attached.
1 140 Speaker assembly For access, remove these FRUs in order: v “1010 Battery pack” on page 67 v “1030 Hard disk drive” on page 69 v “1050 Keyboard” on page 72 v “1090 Keyboard bezel” on page 81 1 Step Screw (quantity) Color T orque 1 M2 × 12 mm, bind-head, nylon-coated (2) Black 0.
In step 3 , release the speaker cables from the cable guide a . 3 2 a When installing: Make sure that the connector 3 is firmly attached.
1 150 IEEE 1394 cable For access, remove these FRUs in order: v “1010 Battery pack” on page 67 v “1030 Hard disk drive” on page 69 v “1050 Keyboard” on page 72 v “1090 Keyboard bezel” on page 81 v “1 140 Speaker assembly” on page 92 Note Some models do not have the IEEE 1394 cable.
4 5 Step Screw (quantity) Color T orque 4 M2 × 6 mm, bind-head, nylon-coated (1) Black 0.245 Nm (2.5 kgfcm) Before remove the IEEE 1394 cable, remove bracket structure 5 .
7 6 Remove the connector 6 . And strip the tape securing the IEEE 1394 cable to the PC Card slot and remove the IEEE 1394 cable 7 . When installing: Make sure that the connector 6 is firmly attached to the system board.
1 160 PC Card slots assembly For access, remove these FRUs in order: v “1010 Battery pack” on page 67 v “1030 Hard disk drive” on page 69 v “1050 Keyboard” on page 72 v “1090 Keyboard be.
1 170 Ultrabay Enhanced shield kit For access, remove these FRUs in order: v “1010 Battery pack” on page 67 v “1020 Ultrabay Enhanced device” on page 68 v “1030 Hard disk drive” on page 69 v “1050 Keyboard” on page 72 v “1090 Keyboard bezel” on page 81 Note: Step 1 is only for the models with 15.
Remove EMI spring for the CDC a and antenna cable guide c before removing the Ultrabay Enhanced shield kit. 2 a 3 Step Screw (quantity) Color T orque 2 M2 × 12 mm, bind-head, nylon-coated (1) Black 0.
Release the antenna cables from the cable guide 4 . 4 4 a b 4 4 4 4 4 4 4 When installing: Make sure that the antenna cables and the two ferrite cores a and b (with sponge) are correctly routed and securely in place.
6 5 5 c When installing: Make sure that the connectors 5 are firmly attached. (continued) Removing and replacing a FRU ThinkPad R50/R50p and R51 Series 101.
For models with M9-32 or M10 GL-128 video chip: 7 8 For models with M7-32 video chip: 7 8 Step Screw (quantity) Color T orque 7 M2 × 12 mm, bind-head, nylon-coated (2) Black 0.
10 9 Step Screw (quantity) Color T orque 9 M2 × 6 mm, bind-head, nylon-coated (1) Black 0.245 Nm (2.5 kgfcm) (continued) Removing and replacing a FRU ThinkPad R50/R50p and R51 Series 103.
11 11 12 13 14 Screws 11 are only for the models with 15.0-in. LCD. For the other models, skip the step. Step Screw (quantity) Color T orque 11 M2 × 10 mm, flat-head, nylon-coated (4) Black 0.245 Nm (2.5 kgfcm) 12 M2 × 3 mm, small-head, nylon-coated (2) Black 0.
1 180 LCD assembly For access, remove these FRUs in order: v “1010 Battery pack” on page 67 v “1050 Keyboard” on page 72 v “1070 Modem daughter card (MDC/MDC-2)” on page 77 v “1080 Bluet.
2 3 4 Step Screw (quantity) Color T orque 2 M2 × 12 mm, bind-head, nylon-coated (1) Black 0.245 Nm (2.5 kgfcm) When installing: Make sure that the connector 4 and the LCD cable retainer 3 are firmly attached, and then secure them with the screw .
7 5 6 Step Screw (quantity) Color T orque 5 M2 × 6 mm, bind-head, nylon-coated (1) Black 0.245 Nm (2.5 kgfcm) 7 M2 × 6 mm, bind-head, nylon-coated (1) Black 0.
8 8 Removing and replacing a FRU 108 R50/R50p, R51 Series.
1 190 VGA and Ultrabay Enhanced device eject button cable For access, remove these FRUs in order: v “1010 Battery pack” on page 67 v “1020 Ultrabay Enhanced device” on page 68 v “1030 Hard d.
3 (continued) Removing and replacing a FRU 11 0 R50/R50p, R51 Series.
VGA and Ultrabay Enhanced device eject button cable is attached to S-Video gasket a . When re-installing the cable, attach the cable as shown in figure b .
1200 System board, interposer card, and base cover For access, remove these FRUs, in order: v “1010 Battery pack” on page 67 v “1020 Ultrabay Enhanced device” on page 68 v “1030 Hard disk dr.
An accelerometer chip for the HDD Active Protection System b is also soldered on the topside of the system board. b (continued) Removing and replacing a FRU ThinkPad R50/R50p and R51 Series 11 3.
Important When handling the system board, bear the following in mind. v The system board of the ThinkPad R50/R50p, and R51 series has an accelerometer , which can be broken by applying several thousands of G-forces.
2 1 3 Step Screw (quantity) Color T orque 1 M2.5 × 4.8 mm, flat-head, nylon-coated (1) Silver 0.392 Nm (4 kgfcm) 2 M2 × 4 mm, flat-head, nylon-coated (2) Black 0.245 Nm (2.5 kgfcm) 3 M2 × 12 mm, bind-head, nylon-coated (1) Black 0.
4 When installing: Make sure that the all the guide holes of the system board are firmly attached to the base cover . (continued) Removing and replacing a FRU 11 6 R50/R50p, R51 Series.
Remove the connector bracket from the system board by removing screws 5 and 6 . Then remove the ac connector from the system board by disconnecting the cables 7 . Step 8 is only for the models with 15.0-in. LCD models. Other models do not have the interposer card.
Note for sticking a label kit on the base cover New base cover FRU is shipped with several kinds of label kit. When you replace the base cover , you need to stick a homologation label a which has the same part no. with the label on the old base cover (defective FRU) on the new base cover .
2010 LCD front bezel For access, remove these FRUs in order: v “1010 Battery pack” on page 67 v “1020 Ultrabay Enhanced device” on page 68 v “1030 Hard disk drive” on page 69 v “1050 Key.
3 2 Removing and replacing a FRU 120 R50/R50p, R51 Series.
2020 Inverter card For access, remove these FRUs in order: v “1010 Battery pack” on page 67 v “1030 Hard disk drive” on page 69 v “1050 Keyboard” on page 72 v “1080 Bluetooth/Modem daugh.
2030 LCD panel, LCD cable assembly , wireless LAN antenna assembly , hinges, and LCD cover For access, remove these FRUs in order: v “1010 Battery pack” on page 67 v “1020 Ultrabay Enhanced devi.
Lift the latch bar in the direction of the arrow 2 , and then remove the left latch in the direction of the arrow 3 . 3 2 When installing: Attach the left latch to the LCD cover as in this figure.
4a 4 4 4 4 4a Step Screw cap Screw (quantity) Color T orque 4 M2 × 4 mm, bind-head, nylon-coated (4) Black 0.245 Nm (2.5 kgfcm) 4a M2 × 4 mm, bind-head, nylon-coated (2) Black 0.
Note: Steps 5 and 6 are only for the models with 15.0-in. SXGA+ LCD, UXGA LCD, and QXGA LCD. For the other models, skip steps 5 and 6 . 10 8 9 7 5 6 5 11 Step Screw (quantity) Color T orque 5 M2 × 4 mm, bind-head, nylon-coated (2) Black 0.
Remove the antenna assembly ( a ). 13 14 12 a Step Screw (quantity) Color T orque 13 M2 × 3 mm, small-head, nylon-coated (2) Silver 0.245 Nm (2.5 kgfcm) Remove the hinges ( b ) from the LCD assembly . 15 15 15 15 16 16 b b Step Screw (quantity) Color T orque 15 M2 × 3 mm, small-head, nylon-coated (4) Silver 0.
T urn over the LCD panel and strip off the tape 17 securing the FPC ( c ). Then detach the connector 18 in the direction of the arrow .
Remove the right latch from the LCD cover . 18 19 When installing: Attach the right latch to the LCD cover as in this figure. Removing and replacing a FRU 128 R50/R50p, R51 Series.
1 2 Removing and replacing a FRU ThinkPad R50/R50p and R51 Series 129.
Routing the cables of the wireless LAN antenna: 1. Place the wireless LAN antennas a and b , and the Bluetooth wireless antenna c under the LCD panel.
3. Route the cables as in the figure below . e e Removing and replacing a FRU ThinkPad R50/R50p and R51 Series 131.
3010 ThinkPad Dock II PCI cover 1 2 1 (Bottom view) Removing and replacing a FRU 132 R50/R50p, R51 Series.
3020 ThinkPad Dock II top cover 1 1 1 (Rear view) Step Screw (quantity) T orque 1 M2.5 × 4.8 mm (3) 0.392 Nm (4 kgfcm) 2 2 2 2 Step Screw (quantity) T orque 2 M2.
3 3 (Bottom view) Step Screw (quantity) T orque 3 M2.5 × 4.8 mm (6) 0.392 Nm (4 kgfcm) (continued) Removing and replacing a FRU 134 R50/R50p, R51 Series.
Make sure that the system lock key A is set to the Unlock position. Release the front latches in step 4 , and then remove the top cover 5 .
Locations Front view 1 Wireless status indicator 2 Bluetooth wireless status indicator (for some models) 3 System and power status indicators 4 External monitor connector 5�.
4 5 6 7 8 14 9 10 11 12 13 15 16 17 R 1 2 3 Locations ThinkPad R50/R50p and R51 Series 137.
Rear view 1 Bluetooth wireless status indicator (for some models) 2 Power status indicators 3 PC Card eject button 4 PC Card slot 5 IEEE 1394 connector (for some models) .
Bottom view 1 Hard disk drive 2 Optional DIMM slot 3 Battery pack 4 Docking connector 5 Battery pack latch 6 Infrared port 7 Built-in stereo speakers 8 .
Parts list Overall 1 2 3 e c 4 7 6 5 6 9 8 11 10 13 14 15 16 17 18 19 20 21 12 f g a b h j i 22 23 d Parts list 140 R50/R50p, R51 Series.
v Each FRU is available for all types or models, unless specific types or models are specified. v A CRU (customer replaceable unit) is identified by a single asterisk (*) or two asterisks (**) in the CRU ID column. An N in the CRU ID column means the part is not a CRU.
No. FRU P/N CRU ID 2 Keyboard bezel assembly for models with 14.1-in. LCD (WW) v 1829-28x, 29x, 43x, 44x, 4Ax, 4Hx, 52x, 53x, 54x, 55x, 56x, 57x, 58x, 59x, 5Bx, 5Gx, 5Hx, 5Jx, 5Lx, 5Mx v 1829-A2x, Cxx.
No. FRU P/N CRU ID 2 Keyboard bezel assembly for models with 15.0-in. LCD (WW) v 1829-33x, 35x, 36x, 37x, 38x, 39x, 3Ax, 3Bx, 3Cx, 3Dx, 3Ex, 3Fx, 63x, 68x, 6Ax, 6Bx, 6Dx, 72x, 73x, 74x, 75x, 76x, 77x,.
No. FRU P/N CRU ID 3 Ultrabay Enhanced shield kit for 14.1-in. v 1829-28x, 29x, 43x, 44x, 4Ax, 4Hx, 52x, 53x, 54x, 55x, 56x, 57x, 58x, 59x, 5Bx, 5Gx, 5Hx, 5Jx, 5Lx, 5Mx v 1829-A2x, Cxx except C4U, CTO.
No. FRU P/N CRU ID 3 Ultrabay Enhanced shield kit for 15.0-in. v 1829-33x, 35x, 36x, 37x, 38x, 39x, 3Ax, 3Bx, 3Cx, 3Dx, 3Ex, 3Fx, 63x, 68x, 6Ax, 6Bx, 6Dx, 72x, 73x, 74x, 75x, 76x, 77x, 78x, 79x, 7Ax, .
No. FRU P/N CRU ID 4 CPU assembly , Mobile Intel Celeron processor , 1.2 GHz v 2887-52x 93P4203 N CPU assembly , Mobile Intel Celeron processor , 1.3 GHz v 2883-2Sx, 2Ux v 2887-22x, 27x, 2Rx, 42x, 43x, 44x, 45x, 53x, 62x, 63x, 64x, 65x, 66x, 67x, 72x, 73x v 2887-9Ux, 9Vx 93P4204 N CPU assembly , Mobile Intel Celeron processor 330 (Cel 1.
No. FRU P/N CRU ID 4 CPU assembly , Intel Pentium M processor , 1.5 GHz v 1829-28x, 35x, 36x, 3Bx, 3Ex, 4Hx, 5Gx, 5Hx, 5Jx, 5Lx, 6Ax, 6Bx, 6Dx, 72x, 7Ax, 7Ex, 7Fx, 7Hx v 1829-A2x, B2x, B5x, C2x, C3x, .
No. FRU P/N CRU ID 4 CPU assembly , Intel Pentium M processor , 1.7 GHz v 1829-7Zx, B3x, B4x, B7x, CMx, CNx, CPx, CQx, CRx, CSx, CTx, CUx, CVx, CWx, CXx, DJx, DKx, DLx, DMx, DNx, DPx, DQx, E3x, E4x, E.
No. FRU P/N CRU ID 4 CPU assembly , Intel Pentium M processor 725 (1.6 GHz) v 1829-KFx, KGx, KHx, KJx, KKx, KLx, KMx, KNx, KPx, KQx, KRx, KSx, KTx, KUx, KVx, L4x, L5x, L6x, L7x v 1829-82x, 83x, 84x, 8.
No. FRU P/N CRU ID 4 CPU assembly , Intel Pentium M processor 745 (1.8 GHz) v 1829-87x, 88x, 89x, 8Ax, 93x, 97x, 9Bx, 9Cx, 9Fx, 9Gx, 9Hx, 9Jx, 9Nx, 9Px, P6x, P8x, PCx, PDx, PQx, PRx, PSx v 1830-9Sx, F.
No. FRU P/N CRU ID 5 ThinkPad Integrated 56K Modem (MDC2) v 1829-A2x, B2x, B3x, Cxx, Dxx, v 1829-Jxx, Kxx except KMx, L8x, LBx, LCx, LFx, LHx v 1829-8xx, 92x, 93x, 97x, 98x, 99x, 9Ax, 9Bx, 9Cx, 9Dx, 9.
No. FRU P/N CRU ID 5 ThinkPad Integrated Bluetooth with 56K Modem (BMDC), Actiontec v 1829-38x, 39x, 72x, 73x, 74x, 75x, 76x, 77x, 7Lx v 1832-22x, 23x, 24x, 25x, 26x, 27x, 28x v 1833-22x, 23x, 24x, 25.
No. FRU P/N CRU ID 6 128-MB DDR SDRAM SO DIMM (PC2700) OP v 2887-2Kx, 2Lx, 45x, 67x v 2887-8Nx, 8Px 31P9829 * 256-MB DDR SDRAM SO DIMM (PC2700) OP v 1829-43x, 44x, 4Ax, 4Hx, 52x, 53x, 54x,.
No. FRU P/N CRU ID 6 256-MB DDR SDRAM SO DIMM (PC2700) OP v 1836-2Nx, 2Px, 2Qx, 2Rx, 2Sx, 2Tx, 2Ux, 3Nx, 3Px, 3Qx, 3Rx, 3Sx, 3Tx, 3Ux v 1836-A4x, A5x, BAx, BBx, BCx, BDx v 1836-GCx, GDx, H7x, H8.
No. FRU P/N CRU ID 6 512-MB DDR SDRAM SO DIMM (PC2700) OP v 1829-74x, 75x, 76x, 77x, 7Lx, 7Mx v 1829-6Yx, 6Zx, 7Yx, 7Zx, CGx, CPx, CTx, CVx, CXx, DNx, DPx, DQx, E2x, E3x, E4x, E5x, E6x, E7x, E9x.
No. FRU P/N CRU ID 8 Interposer card v 1829-33x, 35x, 36x, 37x, 38x, 39x, 3Ax, 3Bx, 3Cx, 3Dx, 3Ex, 3Fx, 63x, 68x, 6Ax, 6Bx, 6Dx, 72x, 73x, 74x, 75x, 76x, 77x, 78x, 79x, 7Ax, 7Dx, 7Ex, 7Fx, 7Hx, 7Jx, 7.
No. FRU P/N CRU ID 8 Interposer card v 2883-2Px, 2Qx, 2Ux, 2Vx v 2883-AKx, ALx, AMx, ARx v 2883-Gxx v 2887-27x, 28x, 29x, 2Ax, 2Bx, 2Lx, 62x, 63x, 64x, 65x, 67x, 72x, 73x, 74x, 75x, 76x, 77x, 78x, 79x.
No. FRU P/N CRU ID 9 Battery pack, Li-ion (6 cell), 4.4 Ah OP v 1829-43x, 44x, 4Ax, 4Hx, 52x, 53x, 54x, 55x, 56x, 57x, 58x, 59x, 5Bx, 5Gx, 5Hx, 5Jx, 5Lx, 5Mx, 63x, 68x, 6Ax, 6Bx, 72x, 75x, 78x, .
No. FRU P/N CRU ID 9 Battery pack, Li-ion (9 cell), 6.6 Ah OP v 1829-6Dx, 73x, 74x, 76x, 77x, 7Ax, 7Jx, 7Kx v 1829-E3x, E5x, EBx, EDx, EGx, 7Zx v 1829-L9x, LCx, LEx, LFx v 1829-92x, 93x, 9Ax, 9C.
No. FRU P/N CRU ID 10 Base cover assembly 1829 15.0-in. WW v 1829-92x, 93x, 94x, 95x, 96x, 97x, 9Fx, 9Gx, 9Hx, 9Jx, 9Kx, 9Lx, 9Mx, 9Nx, 9Px, P3x, P4x, P5x, P6x, P7x, P8x, P9x, P Ax, PBx, PCx, PDx, PEx, PFx, PKx, PLx, PMx, PNx, PPx, PQx, PRx, PSx, PTx 26R8062 N 15.
No. FRU P/N CRU ID 10 Base cover assembly 1831 14.1-in. WW v 1831-48x except 48K, 56x except 56K, 5Ax, 5Cx v 1831-AHx, AJx 13N521 1 N 14.1-in. WW v 1831-8Kx, 8Lx, 8Mx except 8MK, 8Xx, 8Yx 26R8068 N 14.1-in. Korea v 1831-48K, 56K 13N5212 N 14.1-in. Korea v 1831-8MK 26R8069 N 15.
No. FRU P/N CRU ID 10 Base cover assembly 1836 14.1-in. WW v 1836-2Nx, 2Px, 2Qx, 2Rx, 2Sx, 2Tx, 2Ux v 1836-A3x, A4x, A5x 13N5356 N 14.1-in. WW v 1836-Q2x, Q3x, Q8x, Q9x, QAx, QBx 26R8072 N 15.0-in. WW v 1836-3Nx, 3Px, 3Qx, 3Rx, 3Sx, 3Tx, 3Ux v 1836-B8x, B9x, BAx, BBx, BCx, BDx 13N5357 N 15.
No. FRU P/N CRU ID 10 Base cover assembly 2887 14.1-in. WW v 2887-22x, 23x, 24x, 25x, 26x, 2Kx, 2Rx, 42x, 43x, 44x, 45x, 46x, 49x, 52x, 53x, 54x, 55x, 56x, 57x, 58x, 5Ax, 5Bx except 5BK, 5Cx, 5Dx, 5Ex.
No. FRU P/N CRU ID 10 Base cover assembly 2888 14.1-in. WW v 2888-47x except 47K, 4Ax, 5Px, 5Qx, 5Rx v 2888-8Hx except 8HK, 8Rx, 9Qx, 9Rx, 9Sx, 9Tx, 9Nx, 9Px v 2888-ECx, ESx except ESK, ETx, EUx, EVx, EWx, FCx, FGx, FHx, FJx, FLx, FMx, FNx 13R2703 N 14.
No. FRU P/N CRU ID 11 CR-ROM drive, 12.7 mm, HLDS (CRN-8245B-AIBMJ0) v 1829-43x v 1829-D8K v 1829-J2x, J3x v 1829-P2K v 1830-46x, 47x v 1830-AAx v 1832-28x v 1833-28x 92P6565 * CR-ROM drive, 12.
No. FRU P/N CRU ID 11 DVD-ROM drive, 12.7 mm v 1829-44x, 4Ax, 52x, 53x, 58x, 59x, 5Gx, 68x, 6Ax, 78x v 1829-6Zx, 7Yx, C7x, C8x, C9x, CAx, CHx, CJx, CKx, CLx, CPx, CUx, CWx, D6x, DEx, DFx, DKx v 1829-8.
No. FRU P/N CRU ID 11 DVD-ROM drive, 9.5 mm OP v Supported by CTO TEAC (DW-18E) 92P5991 * HLDS (GDR-8083N) 92P6579 * DVD/CD-RW combo drive, 12.7 mm v 1829-4Hx, 54x, 55x, 56x, 57x, 5Bx, 5Gx, 5Hx,.
No. FRU P/N CRU ID 11 DVD/CD-RW combo drive, 12.7 mm v 2883-2Nx, 2Qx v 2883-8Qx, ARx v 2883-ELx, GHx, GJx, GKx v 2887-46x, 49x, 57x, 58x, 5Bx, 5Fx, 5Jx, 5Kx, 5Lx, 5Nx, 63x, 72x, 73x, 74x, 76x, 7Bx, 7C.
No. FRU P/N CRU ID 11 DVD/CD-RW combo drive, 9.5 mm OP v Supported by CTO KME (UJDA745) 92P6581 * T oshiba (SD-R9012) 92P5993 * PCC (UJDA775) 13N6771 * DVD-RAM/RW drive, 12.
No. FRU P/N CRU ID 12 Hard disk drive, 20 GB, 9.5 mm, 4,200 rpm v 1829-JBx, K8x v 2887-2Kx, 2Lx, 45x, 67x v 2888-47x v 2889-48x v 2889-8Lx, APx v 2894-48x v 2895-48x HGST 13N6701 * Fujitsu 27L4385 * Hard disk drive, 30 GB, 9.
No. FRU P/N CRU ID 12 Hard disk drive, 40 GB, 9.5 mm, 4,200 rpm v 1829-4Hx, 58x, 59x, 5Bx, 5Gx, 5Hx, 5Jx, 5Lx, 63x, 6Ax, 6Bx, 6Dx, 72x, 78x, 79x, 7Ax, 7Dx, 7Px v 1829-6Yx, C2x, C5x, CAx, CBx, CDx, CEx.
No. FRU P/N CRU ID 12 Hard disk drive, 40 GB, 9.5 mm, 5,400 rpm v 1829-C4U, D4x, D5x, D7x v 1829-JJx, JKx, K3x, K9x, KCx, KDx, KEx, KHx, KJx v 1830-G6x v 2887-BLx, BMx. BNx v 2887-G2x, H2x, H3x HGST 13N6801 * Fujitsu 13N6773 * Hard disk drive, 60 GB, 9.
No. FRU P/N CRU ID 12 Hard disk drive, 60 GB, 9.5 mm, 7,200 rpm (HGST) v 1832-22x, 23x, 25x, 27x, 28x v 1833-22x, 23x, 25x, 27x, 28x 92P6551 * Hard disk drive, 80 GB, 9.
No. FRU P/N CRU ID 13 Cover , hard disk drive for models with 14.1-in. LCD v 1829-28x, 29x, 43x, 44x, 4Ax, 4Hx, 52x, 53x, 54x, 55x, 56x, 57x, 58x, 59x, 5Bx, 5Gx, 5Hx, 5Jx, 5Lx, 5Mx v 1829-A2x, Cxx exc.
No. FRU P/N CRU ID 13 Cover , hard disk drive for models with 15.1-in. LCD v 1829-33x, 35x, 36x, 37x, 38x, 39x, 3Ax, 3Bx, 3Cx, 3Dx, 3Ex, 3Fx, 63x, 68x, 6Ax, 6Bx, 6Dx, 72x, 73x, 74x, 75x, 76x, 77x, 78x.
No. FRU P/N CRU ID 16 Backup battery 02K7078 N 17 Intel PRO/Wireless LAN 2100 3B Mini PCI Adapter v 1829-4Ax, 4Hx, 53x, 56x, 57x, 58x, 59x, 5Bx, 5Gx, 5Lx, 5Mx, 63x, 68x, 6Ax, 72x, 74x, 75x, 76x, 78x, .
No. FRU P/N CRU ID 17 Intel PRO Wireless 2200BG Mini-PCI Adapter v 1829-CBU, CCU, CDU, D7F , D7U, DHF , DHU, E6F , E6U v 1829-J8F , K4F , KCU, KCF , KEU, KEF , KKF , KTU, KTF , KXF , KZF , LBU, LBF v .
No. FRU P/N CRU ID 17 Intel PRO Wireless 2200BG Mini-PCI Adapter v 1829-C2x, C3x, C4x except C4U, C5x, C6x, C7x, CAx, CBx except CBU, CCx except CCU, CDx except CDU, CEx, CGx, CHx, CLx, CMx, CPx, CSx,.
No. FRU P/N CRU ID 17 Intel PRO Wireless 2200BG Mini-PCI Adapter v 2887-84x, 85x, 87x, 89x, 92x, 93x, 94x, 95x, 96x, 97x, 98x, 99x, 9Ax, 9Bx, 9Cx, 9Dx, 9Ex, 9Gx, 9Hx, 9Jx, 9Kx, 9Lx, A2x, A3x, A5x, A6x.
No. FRU P/N CRU ID 17 ThinkPad 1 1b/g Wireless LAN Mini PCI Adapter v 1830-ALU, ALF , AL V , BVU, BVF , BVV v 2888-4BU, 4BV , 6AU, 6A V v 2887-B7V 91P7416 N v 1830-ALx except ALU, ALF , AL V ; BVx exc.
No. FRU P/N CRU ID 18 System board assembly , Intg 10/100 Ethernet with security chip v 2883-2Mx, 2Nx, 2Px, 2Qx, 2Sx, 2Tx, 2Ux, 2Vx v 2883-8Ex, 8Fx, 8Gx, AKx, ALx, AMx v 2883-Exx, Gxx v 2887-22x, 23x,.
No. FRU P/N CRU ID 18 System board assembly , Intg Gigabit Ethernet with security chip v 2887-26x, 2Bx, 52x, 53x, 54x, 55x, 56x, 57x, 58x, 59x, 5Ax, 5Bx, 5Cx, 5Dx, 5Ex, 5Fx, 5Gx, 5Hx, 5Jx, 5Kx, 5Lx, 5.
No. FRU P/N CRU ID 18 System board assembly , M7-32, 10/100 Ethernet with security chip for R51 series v 1829-C2x, D5x v 1829-J2x, J3x, JCx, K7x v 1829-82x, 83x, P2x, P3x v 1830-AAx, ABx, ACx, BJx v 1.
No. FRU P/N CRU ID 18 System board assembly , M9-32, Gigabit Ethernet with security chip for R51 series v 1829-7Yx, 7Zx, A2x, B2x, B3x, B5x, B6x, B7x, CQx, CRx, CSx, CTx, CUx, CVx, CWx, CXx, DMx, DNx,.
No. FRU P/N CRU ID 18 System board assembly , M7-32, 10/100 Ethernet with security chip, ThinkPad 1 1a/b/g Wireless LAN Mini PCI Adapter II for R51 series v Supported by CTO 27K9920 N System board ass.
No. FRU P/N CRU ID 20 IEEE1394 cable v 1829-28x, 29x, 36x, 37x, 38x, 39x, 3Cx, 3Dx, 3Ex, 3Fx, 52x, 53x, 54x, 55x, 56x, 57x, 58x, 59x, 5Bx, 5Gx, 5Hx, 5Jx, 5Lx, 5Mx, 68x, 6Ax, 6Bx, 6Dx, 72x, 73x, 74x, 7.
No. FRU P/N CRU ID 20 IEEE1394 cable v 2887-26x, 2Bx, 52x, 53x, 54x, 55x, 56x, 57x, 58x, 59x, 5Ax, 5Bx, 5Cx, 5Dx, 5Ex, 5Fx, 5Gx, 5Hx, 5Jx, 5Kx, 5Lx, 5Mx, 5Nx, 72x, 73x, 74x, 75x, 76x, 77x, 78x, 79x, 7.
LCD FRUs 1 2 6 7 8 3 4 k l m n 5 Parts list 188 R50/R50p, R51 Series.
14.1-in. XGA TFT No. FRU P/N CRU ID k- n See “Miscellaneous parts” on page 217. 1 LCD cover kit, 14.1-in. (WW) v 1829-28x, 29x, 43x, 44x, 4Ax, 4Hx, 52x, 53x, 54x, 55x, 56x, 57x, 58x, 59x, 5Bx, 5Gx.
No. FRU P/N CRU ID 2 Hinges, 14.1-in. v 1829-28x, 29x, 43x, 44x, 4Ax, 4Hx, 52x, 53x, 54x, 55x, 56x, 57x, 58x, 59x, 5Bx, 5Gx, 5Hx, 5Jx, 5Lx, 5Mx v 1829-A2x, C2x, C3x, C4x except C4U, C5x, C6K, C7x, C8x.
No. FRU P/N CRU ID 3 LCD cable assembly 14.1-in. XGA, CR v 1829-28x, 29x, 43x, 44x, 4Ax, 4Hx, 52x, 53x, 54x, 55x, 56x, 57x, 58x, 59x, 5Bx, 5Gx, 5Hx, 5Jx, 5Lx, 5Mx v 1829-A2x, C2x, C3x, C4x except C4U,.
No. FRU P/N CRU ID 5 802.1 1a/b/g antenna, 14.1-in. v 1829-28x, 29x, 43x, 44x, 4Ax, 4Hx, 52x, 53x, 54x, 55x, 56x, 57x, 58x, 59x, 5Bx, 5Gx, 5Hx, 5Jx, 5Lx, 5Mx v 1829-A2x, C2x, C3x, C4x except C4U, C5x,.
No. FRU P/N CRU ID 6 Inverter card, XGA v 1829-28x, 29x, 43x, 44x, 4Ax, 4Hx, 52x, 53x, 54x, 55x, 56x, 57x, 58x, 59x, 5Bx, 5Gx, 5Hx, 5Jx, 5Lx, 5Mx v 1829-A2x, C2x, C3x, C4x except C4U, C5x, C6K, C7x, C.
No. FRU P/N CRU ID 7 LCD panel, 14.1-in. XGA v 1829-28x, 29x, 43x, 44x, 4Ax, 4Hx, 52x, 53x, 54x, 55x, 56x, 57x, 58x, 59x, 5Bx, 5Gx, 5Hx, 5Jx, 5Lx, 5Mx v 1829-A2x, C2x, C3x, C4x except C4U, C5x, C6x, C.
15.0-in. XGA TFT No. FRU P/N CRU ID k- n See “Miscellaneous parts” on page 217. 1 LCD cover kit, 15.0-in. (WW) v 1829-33x, 35x, 36x, 37x, 63x, 68x, 6Ax, 6Bx, 6Dx v 1829-6Yx; 6Zx; B2x; B3x; C4U; Dx.
No. FRU P/N CRU ID 2 Hinges, 15.0-in. v 1829-33x, 35x, 36x, 37x, 63x, 68x, 6Ax, 6Bx, 6Dx v 1829-6Yx, 6Zx, B2x, B3x, C4U, Dxx v 1829-Kxx v 1829-Pxx v 1830-67x, 6Bx, 6Fx, 6Hx v 1830-Bxx except BQU, BRGx.
No. FRU P/N CRU ID 3 LCD cable assembly , 15.0-in. XGA v 1829-33x, 35x, 36x, 37x, 63x, 68x, 6Ax, 6Bx, 6Dx v 1829-6Yx, 6Zx, B2x, B3x, C4x, Dxx v 1829-Kxx v 1829-Pxx v 1830-67x, 6Bx, 6Fx, 6Hx v 1830-Bxx.
No. FRU P/N CRU ID 5 802.1 1a/b/g antenna, 15.0-in. v 1829-33x, 35x, 36x, 37x, 63x, 68x, 6Ax, 6Bx, 6Dx v 1829-6Yx, 6Zx, B2x, B3x, C4x, Dxx v 1829-Kxx v 1829-Pxx v 1830-67x, 6Bx, 6Fx, 6Hx v 1830-Bxx ex.
No. FRU P/N CRU ID 6 Inverter card, XGA v 1829-33x, 35x, 36x, 37x, 63x, 68x, 6Ax, 6Bx, 6Dx v 1829-6Yx, 6Zx, B2x, B3x, C4x, Dxx v 1829-Kxx v 1829-Pxx v 1830-67x, 6Bx, 6Fx, 6Hx v 1830-Bxx except BQU, BR.
No. FRU P/N CRU ID 7 LCD panel, 15.0-in. XGA v 1829-33x, 35x, 36x, 37x, 63x, 68x, 6Ax, 6Bx, 6Dx v 1829-6Yx, 6Zx, B2x, B3x, C4U, Dxx v 1829-Kxx v 1829-Pxx v 1830-67x, 6Bx, 6Fx, 6Hx v 1830-Bxx except BQ.
15.0-in. SXGA+ IPS TFT No. FRU P/N CRU ID k- n See “Miscellaneous parts” on page 217. 1 LCD cover kit, 15.0-in. (WW) v 1829-38x, 39x, 3Ax, 3Bx, 3Cx, 3Dx, 3Ex, 3Fx, 72x, 73x, 74x, 75x, 76x, 77x, 78.
No. FRU P/N CRU ID 3 LCD cable assembly , 15.0-in. SXGA+ v 1829-38x, 39x, 3Ax, 3Bx, 3Cx, 3Dx, 3Ex, 3Fx, 72x, 73x, 74x, 75x, 76x, 77x, 78x, 79x, 7Ax, 7Dx, 7Ex, 7Fx, 7Hx, 7Jx, 7Kx, 7Lx, 7Mx, 7Px v 1829-.
No. FRU P/N CRU ID 5 802.1 1a/b/g antenna, 15.0-in. v 1829-38x, 39x, 3Ax, 3Bx, 3Cx, 3Dx, 3Ex, 3Fx, 72x, 73x, 74x, 75x, 76x, 77x, 78x, 79x, 7Ax, 7Dx, 7Ex, 7Fx, 7Hx, 7Jx, 7Kx, 7Lx, 7Mx, 7Px v 1829-7Yx, .
No. FRU P/N CRU ID 7 LCD panel, 15.0 SXGA+ (ID T ech) v 1829-38x, 39x, 3Ax, 3Bx, 3Cx, 3Dx, 3Ex, 3Fx, 72x, 73x, 74x, 75x, 76x, 77x, 78x, 79x, 7Ax, 7Dx, 7Ex, 7Fx, 7Hx, 7Jx, 7Kx, 7Lx, 7Mx, 7Px v 1829-7Yx.
15.0-in. UXGA IPS TFT No. FRU P/N CRU ID k- n See “Miscellaneous parts” on page 217. 1 LCD cover kit, 15.0-in. (WW) v 1832-22x, 23x, 24x, 25x, 27x, 28x v 1833-22x, 23x, 24x, 25x, 27x, 28x 13N5173 N 2 Hinges, 15.0-in. v 1832-22x, 23x, 24x, 25x, 26x, 27x, 28x v 1833-22x, 23x, 24x, 25x, 26x, 27x, 28x 13N5176 N 3 LCD cable assembly 15.
15.0-in. QXGA IPS TFT No. FRU P/N CRU ID k- n See “Miscellaneous parts” on page 217. 1 LCD cover kit, 15.0-in. (WW) v Supported by CTO 13N5173 N 2 Hinges, 15.0-in. QXGA v Supported by CTO 13N5637 N 3 LCD cable assembly 15.0 QXGA v Supported by CTO 91P6837 N 4 Bluetooth wireless antenna, 15.
Keyboard T able 1. Keyboards for 15.0-in. LCD models Language P/N (NMB) P/N (ALPS) CRU ID Arabic 93P4801 93P4861 ** Belgian 93P4796 93P4856 Chinese, T raditional 93P4798 93P4858 Czech 93P4802 93P4862 Danish 93P4789 93P4849 Dutch 93P4786 93P4846 English, U.
T able 2. Keyboards for 14.1-in. LCD models Language P/N (NMB) CRU ID Arabic 08K5065 ** Belgian 08K5060 Chinese, T raditional 08K5062 Czech 08K5066 Danish 08K5053 Dutch 08K5050 English, U.
Recovery CDs For Windows XP Professional (R50/R50p series) Windows XP Professional is preinstalled as the operating system in the following models: v 1829-4Gx, 4Hx, 54x, 56x, 58x, 5Hx, 63x, 68x, 6Ax, .
For Windows XP Professional (R51 series) Windows XP Professional is preinstalled as the operating system in the following models: v 1829-C2x, C4x, C9x, CBx, CCx, CDx, CKx, CMx, CNx, CQx, CRx, D2x, D4x.
Language P/N CRU ID Arabic 24R5467 * Chinese, Simplified 24R5460 Chinese, T raditional 24R5461 Chinese, T raditional (Hong Kong S.A.R.) 24R5462 Czech 24R5466 Danish 24R5456 Dutch 24R5459 English, U.
v 2883-2Nx, 2Qx, 2Xx, 2Yx, 2Zx v 2883-8Qx, ARx v 2883-ELx, GHx, GJx, GKx, v 2887-2Rx, 32x, 42x, 43x, 46x, 49x, 53x, 54x, 55x, 57x, 5Cx, 5Ex, 5Fx, 5Gx, 5Jx, 62x, 63x, 64x, 65x, 72x, 74x, 77x, 7Kx, 7Bx,.
Language P/N CRU ID Arabic 39K6289 * Chinese, Simplified 39K6282 Chinese, T raditional 39K6283 Chinese, T raditional (Hong Kong S.A.R.) 39K6284 Czech 39K6288 Danish 39K6278 Dutch 39K6281 English, U.
For Windows XP Home Edition (R50/R50p series) Windows XP Home Edition is preinstalled as the operating system in the following models: v 1829-43x, 44x, 4Ax, 52x, 53x, 55x, 57x, 59x, 5Bx, 5Gx, 5Jx, 5Lx.
For Windows XP Home Edition (R51 series) Windows XP Home Edition is preinstalled as the operating system in the following models: v 1829-C3x, C5x, C6x, C7x, C8x, CAx, CEx, CFx, CGx, CHx, CJx, CLx, CPx.
v 2887-2Kx, 2Lx, 44x, 45x, 52x, 56x, 58x, 59x, 5Ax, 5Bx, 5Dx, 5Hx, 5Kx, 5Mx, 5Nx, 5Sx, 5Tx, 5Ux, 66x, 67x, 73x, 75x, 76x, 7Ax, 7Cx, 7Hx, 7Qx v 2887-85x, 87x, 8Nx, 8Px, 94x, 95x, 96x, 97x, 9Ax, 9Cx, 9D.
Miscellaneous parts FRU P/N CRU ID Screw kit (including nylon-coated screws): v M2.5 × 4.8 mm (black), bind-head (8) v M2 × 4 mm (black), bind-head (14) v M2 × 6 mm (black), bind-head (4) v M2 × 12 mm (black), flat-head (17) v M2 × 10 mm (black), flat-head (9) v Hex stud (4) v M2 × 18.
FRU P/N CRU ID Base miscellaneous parts for 2887, 2888: v Cover , PC Card slot v Spring, PC Card slot cover v Rubber foot (rear) v Rubber foot (front) v Insulation, bottom v Insulation sheet v Insulat.
FRU P/N CRU ID 14.1-in. LCD miscellaneous parts: v ( k ) LCD latch assembly , 14 (L) v ( l ) LCD latch, 14 (R) v ( m ) Lower cable bush, 14 v ( n ) Upper cable bush, 14 v Finger , LCD FPC 14 v Screw caps (not painted) v Screw caps, square Note: Italicized letters in parentheses are references to the exploded view on page 188.
FRU P/N CRU ID System miscellaneous parts for 2887, 2888: v ( a ) Cable, RJ1 1-docking connector on system board v ( b ) Antenna cable guide v ( c ) EMI spring, CDC v ( e ) DC in cable v ( f ) Bracket.
Optional FRUs FRU P/N CRU ID 128-MB DDR SDRAM SO DIMM (PC2100) 10K0029 * 256-MB DDR SDRAM SO DIMM (PC2100) 10K0031 * 512-MB DDR SDRAM SO DIMM (PC2100) 10K0033 * 1-GB DDR SDRAM SO DIMM (PC2100) 10K0035 * Ultrabay Enhanced hard disk drive adapter 62P4553 * Optional adapter for 12.
Common parts list T ools T ool P/N T riconnector wrap plug 72X8546 PC test card 35G4703 Audio wrap cable 66G5180 USB parallel test cable 05K2580 Screwdriver kit 95F3598 Mini PC tool set 00P7033 Removal tool antenna RF connector 08K7159 USB floppy disk drive for maintenance diskette 05K9283 ThinkPad Hardware Maintenance Diskette V ersion 1.
For 3-pin power cords: Region P/N CRU ID Australia, New Zealand 76H3514 * T aiwan, Thailand 76H3516 Italy 76H3530 Denmark 76H3520 U.K., China (Hong Kong S.A.R.) 76H3524 European countries 76H3518 India, South Africa 76H3522 Israel 76H3532 Korea 76H3535 China (P .
Notices Lenovo may not offer the products, services, or features discussed in this document in all countries. Consult your local Lenovo representative for information on the products and services currently available in your area.
and is presented as an illustration. The result obtained in other operating environments may vary . Lenovo may use or distribute any of the information you supply in any way it believes appropriate without incurring any obligation to you.
T rademarks The following terms are trademarks of Lenovo in the United States, other countries or both: Lenovo Rescue and Recovery ThinkLight ThinkPad ThinkPad Dock II ThinkPad Mini Dock ThinkPad Port.
T rademarks ThinkPad R50/R50p and R51 Series 227.
Part Number: 39T6190 (1P) P/N: 39T6190.
Ein wichtiger Punkt beim Kauf des Geräts Lenovo R50p (oder sogar vor seinem Kauf) ist das durchlesen seiner Bedienungsanleitung. Dies sollten wir wegen ein paar einfacher Gründe machen:
Wenn Sie Lenovo R50p noch nicht gekauft haben, ist jetzt ein guter Moment, um sich mit den grundliegenden Daten des Produkts bekannt zu machen. Schauen Sie zuerst die ersten Seiten der Anleitung durch, die Sie oben finden. Dort finden Sie die wichtigsten technischen Daten für Lenovo R50p - auf diese Weise prüfen Sie, ob das Gerät Ihren Wünschen entspricht. Wenn Sie tiefer in die Benutzeranleitung von Lenovo R50p reinschauen, lernen Sie alle zugänglichen Produktfunktionen kennen, sowie erhalten Informationen über die Nutzung. Die Informationen, die Sie über Lenovo R50p erhalten, werden Ihnen bestimmt bei der Kaufentscheidung helfen.
Wenn Sie aber schon Lenovo R50p besitzen, und noch keine Gelegenheit dazu hatten, die Bedienungsanleitung zu lesen, sollten Sie es aufgrund der oben beschriebenen Gründe machen. Sie erfahren dann, ob Sie die zugänglichen Funktionen richtig genutzt haben, aber auch, ob Sie keine Fehler begangen haben, die den Nutzungszeitraum von Lenovo R50p verkürzen könnten.
Jedoch ist die eine der wichtigsten Rollen, die eine Bedienungsanleitung für den Nutzer spielt, die Hilfe bei der Lösung von Problemen mit Lenovo R50p. Sie finden dort fast immer Troubleshooting, also die am häufigsten auftauchenden Störungen und Mängel bei Lenovo R50p gemeinsam mit Hinweisen bezüglich der Arten ihrer Lösung. Sogar wenn es Ihnen nicht gelingen sollte das Problem alleine zu bewältigen, die Anleitung zeigt Ihnen die weitere Vorgehensweise – den Kontakt zur Kundenberatung oder dem naheliegenden Service.
