Benutzeranleitung / Produktwartung iF23 des Produzenten AOC
Zur Seite of 63
iF23 LCD Monitor User Manual.
2 Safety ............................................................................................................................... ......................................... 4 National C onventio ns ...............................................
3 HG Declar atio n ................................................................................................................ ................................ 5 8 EPEA T Declar ation ..............................................................
4 Safety National Conventions The following subsections desc ribe notational conventions used in this document. Notes, Cautions, and W arni ngs Throughout this guide, blocks of text ma y be accomp anied by an icon and printe d in bold type or in italic type.
5 Power The monitor should be operat ed only from the type of power source indicated on the lab el. If you are not sure of the type of power supplied to your hom e, consult your dealer or local power company . The monitor is equipped with a three-pronged grounded plug, a plu g with a third (grounding) pin.
6 Inst allation Do not place the monitor on a n unstable cart, stand, tripod, bracket, or table. If the monitor falls, it can injure a person and cause serious damage to this product. Use only a cart, stand, tripod, bracket, or table recommended by the manufacturer or sold with this product.
7.
8 Cleaning Clean the cabinet regularly with the cloth provided. Y ou can use soft-detergent to wipe out the stain, instead of strong-detergent which will c auterize the product cabinet. When cleaning, make sure no detergent is leaked into the product.
9 Other If the product is emitting a strange smell, sound or smoke, disconnect the po wer plug IMMEDIA TEL Y and contact a Service Center . Make sure that the ventilating ope nings are not blocked by a table or curtain. Do not engage the LCD monitor in severe vib ration or high impact conditions during operation.
10 Setup Content s in Box Not all signal cables (Analog, DVI, and HDMI cables) wi ll be provided for all countries and regions. Pleas e check with the local dealer or AOC branch office for confirmation.
11 Setup S t and & Base Please setup or remove the base follo wing the step s as below . Setup: Remove:.
12 Adjusting V iewing Angle For optimal viewing it is recommended to look at the full fa ce of the monitor , then adjust the monitor's angle to your own preference. Hold the stand so you will not toppl e the moni tor when you change the monitor's angl e.
13 Connecting the Monitor Cable Connections On Back of Monitor and Computer: 1. Power 2. Analog (DB-15 VGA cable) 3.DVI T o protect equipment, always turn off the PC and LCD monitor before connecting. 1 Connect the po wer cable to the AC port on the back of the monitor .
14 W all Mounting Preparing to Install An Optional Wall Mounting Arm. This monitor can be attached to a wall mounting arm you p urchase separately . Disconnect power before this procedure. Follow these steps: 1 Remove the bas e. 2 Follow the manufacturer' s instructi ons to assemb le the wall mounting arm.
15 Adjusting Setting Optimal Resolution Windows Vist a For Window s Vista: 1 Click ST A RT . 2 Click CONTROL P ANEL. 3 Click Appearance and Personalization.
16 5 Click Display Settings. 6 Set the resolution SLIDE-BAR to 1920 by 1080..
17 Windows XP For Windows XP: 1 Click ST A RT . 2 Click SETTINGS. 3 Click CONTROL P ANEL. 4 Click Appearan ce and Themes. 5 Double click DISPLA Y ..
18 6 Click SETTINGS. 7 Set the resolution SLIDE-BAR to 1920 by 1080. Windows ME/2000 For Windows ME/2000: 1 Click ST A RT . 2 Click SETTINGS. 3 Click CONTROL P ANEL. 4 Double click DISPLA Y . 5 Click SETTINGS. 6 Set the resolution SLIDE-BAR to 1920 by 1080.
19 Hotkeys Power Key Press the Power button continuously about 2 secon d to turn of f the monitor . Eco Mode and DCR hot key Press the Eco key continuously to select the Eco m ode of brightness an d DCR on when there is no OSD ( Eco mode hot key may not be available in all mode ls).
20 OSD Setting Basic and simple instruction on the control keys. 1) Press Menu (Power) button to activate the OSD window . Press lef t, right, up, do wn button to navigate through the functions. Once the desired function is highlig hted, press Menu (Power) button to activate submenu .
21 Luminance.
22 Brightness 0-100 Backlight Adju stment Contrast 0-100 Contra st from Digital-register. Eco mode Standard Standard Mode Tex t Text Mode Internet Internet Mode Game Game Mode Movie Movie Mode Sports .
23 Image Setup.
24 Clock 0-100 Adjust picture Clock to reduce Vertical-Line noise. Phase 0-100 Adjust Picture Phase to reduce Horizontal-Line noise H.Position 0-100 Adjust the horizontal positio n of the picture. V.Position 0-100 Adjust the verticalposition of the picture.
25 Color T emperature.
26 Warm 6500K Recall Warm Color Temperature from EEPROM. Normal 7300K Recall Normal Color T emperature from EEPROM. Cool 9300K Recall Cool Color T emperature from EEPROM. sRGB Recall SRGB Color Temperature from EEPROM. User Red Red Gain from Digital-register Green Green Gain Digital-register.
27 Color Boost.
28 Full Enhance on or off Disable or Enable Full Enhan ce Mode Nature Skin on or off Disable or Enable Nature Skin Mode Green Field on or off Disable or Enable Green Field Mode Sky-blue on or off Disa.
29 Picture Boost.
30 Frame Size 14-100 Adjust Frame Size Brightness 0-100 Adjust Frame Brightness Contrast 0-100 Adjust Frame Contrast H. position 0-100 Adjust Frame horizontal Position V.
31 OSD Setup.
32 OSD Setup H.Position 0-100 Adjust the horizontal position of OSD V.Position 0-100 Adjust t he verti cal position of OSD Timeout 5-120 Adjust the OSD Timeout Transparence 0-100 Adjust the transparen.
33 Extra.
34 Input Select A uto Select to Auto De tect input signal A nalog Select Analog Sigal Source as Input Digital Select Digital Sigal Source as Input A uto Config yes or no A uto adjust the picture to de.
35 Reset.
36 Reset yes or no Reset the menu to default.
37 Exit Exit Exit the main OSD.
38 LED Indicator Stat us LED Color Full Power Mode Blue Active-off Mode Orange.
3 9 Windows 2000 1. S tart Window s® 2000 2. Click on the 'S tart' button, point to 'S ettings', and then click on 'Control Pane l'. 3. Double click on the 'Display' Icon. 4. Select the 'Settings' tab then click on 'Advanced.
4 0 Windows XP 1. S tart Window s® XP 2. Click on the 'S tart' button and t hen click on 'Control Panel'. 3. Select and click on the categor y ‘Appearance and Themes’ 4.
4 1 5. Select the 'Settings' tab then click on the 'Advanced' butt on. 6. Select 'Monitor' tab - If the 'Properties' button is inactive, it means your m onitor is properly configur ed. Please stop installation. - If the 'Properties' button is active, click on 'Properties' button.
4 2 8. Select the 'Install from a list or specific location [ advanced]' radio button and then click on the 'Next' button. 9. Select the 'Don't Search. I will choose the driver to install' radio button. Then click on the 'Next' button.
4 3 Windows Vist a 1. Click "S tart " and "Control Panel". Then, doubl e-click on "Appearance and Personaliz ation". 2. Click "Personalization" and then "Display Settings". 3. Click "Advanced Settings.
4 4 4. Click "Properties" in the "Monitor" tab. If the "Properties" button is deactivated, it means the configuration for your monitor is completed. The monitor can be used as is. If the message "Windows needs..." is displayed, as shown in the figure below , click "Continue".
39 Windows 7 1.S tart Windows® 7 2.Click on the 'St art' button and then click on 'Control Panel'. 3. Click on the 'Display' icon.
4 6 5. Click the “ A dvanced Settings” button. 6. Click the “Monitor” tab and then click the “Properties” button. 7.Click the “Driver” tab.
4 7 8. Open the "Update Driver Soft w are-Generic PnP Monitor" window by clicking on “Update Driver... “ and then click the "Browse my computer for driver software" button. 9. Select "Let me pick from a list of device driv ers on my computer" .
4 8 11. Select the "xxx.inf" file and click the “Open” button. Click the “OK” button. 12. Select your monitor model and click the “Next” button. The files will be copi ed from the CD to your hard disk drive. 1 3. Close all open windows and remove the CD.
49 i-Menu Welcome to “i-Menu” software by AOC. i-Menu makes it eas y to adjust your monitor display setting by using on screen menus instead of the OSD button on the monitor .
5 0 T roubleshoot Problem & Question Possible Solutions Power LED Is Not ON Make sure the power button is ON and the Power Cord is properly connecte d to a grounded power outlet and to the monitor . No images on the screen Is the power cord connected properly? Check the power cord connection and po wer supply .
5 1 Monitor Is Stu ck In A ctive Off-Mode" The Computer Power Switch should be in the ON position. The Computer Video Card should be snugly fitted in its slot. Make sure the monitor's video cable is prop erly connected to the computer . Inspect the monitor's video cable and mak e sure no pin is bent.
5 2 S pecification General S pecification LCD Panel Model number iF23 Driving system TFT Color LCD Viewable Image Size 58 . 4 c m diagonal Pixel pitch 0.265mm(H) x 0.265mm(V) Video R, G , B Analog lnterface & Digital Interface Separate Sy nc. H/V TTL Display Color 16.
5 3 Preset Display Modes VGA 640 x 480 @60 Hz 31.469 59.940 VGA 640 x 480 @72 Hz 37.861 72.809 VGA 640 x 480 @75 Hz 37.500 75.000 SVGA 800 x 600 @56 Hz 35.156 56.250 SVGA 800 x 600 @60 Hz 37.879 60.317 SVGA 800 x 600 @75 Hz 46.875 75.000 Mac-mode 832 x 624 @75 Hz 49.
5 4 Pin Assignment s Pin Number 15-Pin Side of the Signal Cable 1 Video-Red 2 Video-Green 3 Video-Blue 4 N.C. 5 Detect Cable 6 GND-R 7 GND-G 8 GND-B 9 +5V 10 Ground 11 N.
5 5 Pin No. Signal Name Pin No. Signal Name Pin No. Signal Name 1 TMDS Data 2- 9 TMDS Data 1- 17 TMDS Data 0- 2 TMDS Data 2+ 10 TMDS Data 1+ 18 TM DS Data 0+ 3 TMDS Data 2/4 Shield 11 TMDS Data 1/3 Sh.
5 6 Plug and Play Plug & Play DDC2B Feature This monitor is equipped wi th VESA DDC2B capabilities according to the VESA DDC ST ANDARD. It allow s the monitor to inform the host system of its identity and, dependi ng on the level of DDC used, communicate additional information about its display capabilities.
5 7 Regulation FCC Notice FCC Class B Radio Freq uency Interference St atement WA RNING: (FOR FCC CERTIFIED MODELS) NOTE: This equipment has been tested and found to compl y with the limits for a Class B digit al device, pursuant t o Part 15 of the FCC Rules.
5 8 WEEE Declaration Disposal of W aste Equipment by Users in Pr ivate Household in the Europe an Union. This symbol on the product or on its packaging indicates t hat this product must not be di sposed of with your other household wast e.
59 EPEA T Declaration EPEA T is a system to help purchasers in the public an d priv ate sectors evaluate, compare and select desktop computers, notebooks and monitors ba sed on their environmental attributes .
6 0 Service W arranty St atement for Europe LIMITED THREE-YEAR W ARRANTY* AOC Color Monitors sold within Europe AOC International (Europe) GmbH warrant s this product to be free from defects in material and workmanship for a period of Three (3) years after the original date of c onsumer purchase.
6 1 modified or altered; you bear the sole responsibility and liabilit y for any such modification or alteration. ALL EXPRESS AND IMPLIED W ARRANTIES FOR THIS PRODUCT (INCLUDING THE WARRANTIES OF MERC.
6 2 W arranty S t atement for North & South America (excluding Brazil) W ARRANTY ST A TEMENT for AOC Color Monitors Including those Sold w ithin North America as S pecified Envision Peripherals, Inc.
6 3 ALL EXPRESS AND IMPLIED W ARRANTIES FOR THIS PRODUCT (INCLUDING THE WARRANTIES OF MERCHANT ABILIT Y AND FITNESS FOR A P ARTICULAR PURPOSE) ARE LIMITED IN DURA TION TO A PERIOD OF THREE (3) YEARS FOR P ARTS AND LABOR AND ONE (1) YEAR FOR CRT TUBE OR LCD P ANEL FROM THE ORIGINAL DA TE OF CONSUMER PURCHASE.
Ein wichtiger Punkt beim Kauf des Geräts AOC iF23 (oder sogar vor seinem Kauf) ist das durchlesen seiner Bedienungsanleitung. Dies sollten wir wegen ein paar einfacher Gründe machen:
Wenn Sie AOC iF23 noch nicht gekauft haben, ist jetzt ein guter Moment, um sich mit den grundliegenden Daten des Produkts bekannt zu machen. Schauen Sie zuerst die ersten Seiten der Anleitung durch, die Sie oben finden. Dort finden Sie die wichtigsten technischen Daten für AOC iF23 - auf diese Weise prüfen Sie, ob das Gerät Ihren Wünschen entspricht. Wenn Sie tiefer in die Benutzeranleitung von AOC iF23 reinschauen, lernen Sie alle zugänglichen Produktfunktionen kennen, sowie erhalten Informationen über die Nutzung. Die Informationen, die Sie über AOC iF23 erhalten, werden Ihnen bestimmt bei der Kaufentscheidung helfen.
Wenn Sie aber schon AOC iF23 besitzen, und noch keine Gelegenheit dazu hatten, die Bedienungsanleitung zu lesen, sollten Sie es aufgrund der oben beschriebenen Gründe machen. Sie erfahren dann, ob Sie die zugänglichen Funktionen richtig genutzt haben, aber auch, ob Sie keine Fehler begangen haben, die den Nutzungszeitraum von AOC iF23 verkürzen könnten.
Jedoch ist die eine der wichtigsten Rollen, die eine Bedienungsanleitung für den Nutzer spielt, die Hilfe bei der Lösung von Problemen mit AOC iF23. Sie finden dort fast immer Troubleshooting, also die am häufigsten auftauchenden Störungen und Mängel bei AOC iF23 gemeinsam mit Hinweisen bezüglich der Arten ihrer Lösung. Sogar wenn es Ihnen nicht gelingen sollte das Problem alleine zu bewältigen, die Anleitung zeigt Ihnen die weitere Vorgehensweise – den Kontakt zur Kundenberatung oder dem naheliegenden Service.
