Benutzeranleitung / Produktwartung OPERATORS MANUAL CS 2156C des Produzenten Husqvarna
Zur Seite of 44
English CS 2156, CS 2156C CS 2156CWH CS 2159, CS 2159W CS 2159WH CS 2159C CS 2159CWH Operator ′ s manual Please read the operator’ s manual carefully and make sure y ou understand the instructions before using the machine.
KEY T O SYMBOLS 2 – English Symbols on the machine: W ARNING! Chain saws can be dangerous! Careless or incorrect use can result in serious or fatal injury to the operator or others. Please read the operator’ s manual carefully and make sure y ou understand the instructions before using the machine.
CONTENTS English – 3 Contents KEY T O SYMBOLS Symbols on the machine: ..................................... 2 Symbols in the operator’ s manual: ....................... 2 CONTENTS Contents ..........................................................
4 – English INTR ODUCTION Dear Customer , Cong ratulations on y our choice to buy a Jonsered product! W e are convinced that you will appreciate with g reat satisfaction the quality and perf or mance of our product f or a very long time to come .
English – 5 WHA T IS WHA T? What is what on the c hain saw? 1 Cylinder cov er 2 F ront handle 3 Chain brak e and front hand guard 4 Star ter 5 Chain oil tank 6 Star ter handle 7 Adjuster screws carb urettor 8 Choke control/Start throttle lock 9 Rear handle 10 Stop s witch (Ignition on/off switch.
GENERAL SAFETY PRECA UTIONS 6 – English Bef ore using a new c hain saw • Please read this manual carefully . • Check that the cutting equipment is correctly fitted and adjusted. See instr uctions under the heading Assembly . • Refuel and star t the chain saw .
GENERAL SAFETY PRECA UTIONS English – 7 pro vide inf or mation about which training materials and courses are a v ailable . W or k is constantly in progress to impro ve the design and technology - impro v ements that increase y our saf ety and efficiency .
GENERAL SAFETY PRECA UTIONS 8 – English • The brak e is applied when the front hand guard (B) is pushed f orwards. • This mov ement activates a spring-loaded mechanism that tightens the brak e band (C) around the engine drive system (D) (clutch drum).
GENERAL SAFETY PRECA UTIONS English – 9 of the front hand guard, the chain brak e can only be activated b y the iner tia action. Will m y hand alwa ys activate the c hain brake during a kickbac k? No . It takes a certain force to mov e the hand guard f orward.
GENERAL SAFETY PRECA UTIONS 10 – English chain saw , including the cutting equipment, is insulated from the handles by vibr ation damping units. Cutting hardwoods (most broadleaf trees) creates more vibr ation than cutting softwoods (most conif ers).
GENERAL SAFETY PRECA UTIONS English – 11 • Keep the chain pr operly tensioned! If the chain is slack it is more lik ely to jump off and lead to increased wear on the bar , chain and dr iv e sprocket.
GENERAL SAFETY PRECA UTIONS 12 – English Sharpening y our chain and adjusting depth gauge setting General inf ormation on sharpening cutting teeth • Ne ver use a blunt chain. When the chain is blunt y ou hav e to ex er t more pressure to force the bar through the wood and the chips will be v ery small.
GENERAL SAFETY PRECA UTIONS English – 13 General advice on adjusting depth gauge setting • When you sharpen the cutting tooth (A) the depth gauge setting (C) will decrease. T o maintain optimal cutting perf or mance the depth gauge (B) has to be filed down to achie v e the recommended depth gauge setting.
GENERAL SAFETY PRECA UTIONS 14 – English Lubricating cutting equipment Chain oil Chain oil must demonstrate good adhesion to the chain and also maintain its flow characteristics regardless of whether it is warm summer or cold winter weather .
GENERAL SAFETY PRECA UTIONS English – 15 Regular ly check the degree of wear on the driv e sprocket. Replace if wear is e xcessive . Replace the dr iv e sprocket whene ver you replace the chain. Needle bearing lubrication Both v ersions of sproc kets ha ve a needle bearing on the drive shaft, which has to be greased regularly (once a week).
ASSEMBL Y 16 – English Fitting the bar and chain Check that the chain br ake is in disengaged position by moving the front hand guard to wards the front handle. Remov e the bar n uts and remo v e the clutch co v er (chain br ak e). T ake off the transportation r ing (A).
FUEL HANDLING English – 17 Fuel Note! The machine is equipped with a two-strok e engine and must alwa ys be run using a mixture of petrol and two- stroke oil. It is impor tant to accurately measure the amount of oil to be mix ed to ensure that the correct mixture is obtained.
FUEL HANDLING 18 – English Fuelling Clean the area around the fuel cap . Clean the fuel and chain oil tanks regularly . The fuel filter must be replaced at least once a year . Contamination in the tanks causes malfunction. Make sure the fuel is well mix ed by shaking the container bef ore refuelling.
ST ARTING AND ST OPPING English – 19 Star ting and stopping Cold engine Starting: The chain brake must be engaged when the chain saw is started. Activate the brak e by mo ving the front hand guard f orwards. Ignition; choke: Set the chok e control in the choke position.
ST ARTING AND ST OPPING 20 – English Push in the choke control as soon as the engine fires and keep pulling until the engine starts. When the engine star ts, quic kly apply full throttle; the throttle star t lock will automatically disengage.
W ORKING TECHNIQUES English – 21 Bef ore use: 1 Check that the chain br ak e works correctly and is not damaged. 2 Check that the rear right hand guard is not damaged. 3 Check that the throttle loc kout works correctly and is not damaged. 4 Check that the stop s witch works correctly and is not damaged.
W ORKING TECHNIQUES 22 – English Fit a guard to the bar bef ore transpor ting the chain saw or carrying it for an y distance. 7 When you put the chain sa w on the ground, lock the sa w chain using the chain br ake and ensure you ha ve a constant view of the machine .
W ORKING TECHNIQUES English – 23 the saw chain is jamming, the sa w may be pushed back at y ou. 8 Unless the user resists this pushing f orce there is a r isk that the chain saw will mo ve so f ar backwards that only the kickbac k zone of the bar is in contact with the tree, which will lead to a kic kback.
W ORKING TECHNIQUES 24 – English Limbing When limbing thick br anches you should use the same approach as f or cutting. Cut difficult branches piece b y piece. Cutting If you ha ve a pile of logs , each log you attempt to cut should be remov ed from the pile, placed on a saw horse or runners and cut individually .
W ORKING TECHNIQUES English – 25 Felling direction The aim is to f ell the tree in a position where you can limb and cross-cut the log as easily as possible .
W ORKING TECHNIQUES 26 – English Ne xt make the bottom cut so that it finishes e xactly at the end of the top cut. The directional cuts should run 1/4 of the diameter through the trunk and the angle between the top cut and bottom cut should be 45 ° .
W ORKING TECHNIQUES English – 27 Freeing a tree that has fallen badl y Freeing a ”trapped tree” It is very dangerous to remov e a trapped tree and there is high accident risk. Ne ver try to fell the tree that is trapped. Ne ver work in the risk zone of the hanging trapped tree.
W ORKING TECHNIQUES 28 – English Ho w to a v oid kickbac k What is kic kback? The word kic kback is used to describe the sudden reaction that causes the chain saw and bar to jump off an object when the upper quadrant of the tip of the bar , known as the kic kback zone , touches an object.
MAINTENANCE English – 29 General The user must only carry out the maintenance and ser vice work described in this manual. Carb urettor adjustment Due to e xisting environmental and emissions legislation your chain sa w is equipped with movement limiters on the carburettor adjuster scre ws.
MAINTENANCE 30 – English e very position and the engine speed should be safely below the speed at which the chain starts to rotate. High speed jet H At the factory the engine is adjusted at sea level.
MAINTENANCE English – 31 Checking the inertia brake release Place the chain saw , with the engine s witched off, on a stump or other stable surf ace. Release the front handle and let the saw f all by its o wn weight, rotating around the rear handle tow ards the stump.
MAINTENANCE 32 – English Chain catcher Chec k that the chain catcher is not damaged and is firmly attached to the body of the chain saw . Right hand guar d Chec k that the right hand guard is not damaged and that there are no visible def ects, such as crac ks.
MAINTENANCE English – 33 The muffler is designed to reduce the noise le vel and to direct the e xhaust gases awa y from the operator . The e xhaust gases are hot and can contain spar ks, which ma y cause fire if directed against dr y and comb ustible material.
MAINTENANCE 34 – English Fitting the starter • T o fit the star ter , first pull out the star ter cord and place the star ter in position against the crankcase. Then slowly release the starter cord so that the pulley engages with the pawls . • Fit and tighten the screws that hold the starter .
MAINTENANCE English – 35 Adjustment of the oil pump The oil pump is adjustable . Adjustments are made by turning the screw using a screwdriver or combination spanner .
MAINTENANCE 36 – English Winter use Running problems can occur when using the machine in the cold and snowy conditions caused b y: • T oo low engine temperature .
English – 37 MAINTENANCE Maintenance schedule The f ollowing is a list of the maintenance that must be perf ormed on the machine. Most of the items are described in the Maintenance section. Daily maintenance W eekly maintenance Monthly maintenance Clean the outside of the machine.
38 – English TECHNICAL D A T A T echnical data Note 1: Noise emissions in the environment measured as sound po wer (L WA ) in conf or mity with EC directive 2000/14/ EC .
English – 39 TECHNICAL D A T A Bar and chain combinations The f ollowing cutting attachments are approv ed for the models Jonsered CS 2156, CS 2156C , CS 2156CWH, CS 2159, CS 2159W , CS 2159WH, CS 2159C and CS 2159CWH. Sa w c hain filing and file gaug es Bar Chain Length, inch Pitch, inch Gauge, mm Max.
40 – English TECHNICAL D A T A EC-declaration of conf ormity (Applies to Eur ope only) Husqvarna AB , SE-561 82 Huskvarna, Sweden, tel: +46-36-146500, declares under sole responsibility that the cha.
.
.
.
1153185-26 ´®z+U2T¶6X¨ ´®z+U2T¶6X¨ 2010-03-22 Original instructions.
Ein wichtiger Punkt beim Kauf des Geräts Husqvarna OPERATORS MANUAL CS 2156C (oder sogar vor seinem Kauf) ist das durchlesen seiner Bedienungsanleitung. Dies sollten wir wegen ein paar einfacher Gründe machen:
Wenn Sie Husqvarna OPERATORS MANUAL CS 2156C noch nicht gekauft haben, ist jetzt ein guter Moment, um sich mit den grundliegenden Daten des Produkts bekannt zu machen. Schauen Sie zuerst die ersten Seiten der Anleitung durch, die Sie oben finden. Dort finden Sie die wichtigsten technischen Daten für Husqvarna OPERATORS MANUAL CS 2156C - auf diese Weise prüfen Sie, ob das Gerät Ihren Wünschen entspricht. Wenn Sie tiefer in die Benutzeranleitung von Husqvarna OPERATORS MANUAL CS 2156C reinschauen, lernen Sie alle zugänglichen Produktfunktionen kennen, sowie erhalten Informationen über die Nutzung. Die Informationen, die Sie über Husqvarna OPERATORS MANUAL CS 2156C erhalten, werden Ihnen bestimmt bei der Kaufentscheidung helfen.
Wenn Sie aber schon Husqvarna OPERATORS MANUAL CS 2156C besitzen, und noch keine Gelegenheit dazu hatten, die Bedienungsanleitung zu lesen, sollten Sie es aufgrund der oben beschriebenen Gründe machen. Sie erfahren dann, ob Sie die zugänglichen Funktionen richtig genutzt haben, aber auch, ob Sie keine Fehler begangen haben, die den Nutzungszeitraum von Husqvarna OPERATORS MANUAL CS 2156C verkürzen könnten.
Jedoch ist die eine der wichtigsten Rollen, die eine Bedienungsanleitung für den Nutzer spielt, die Hilfe bei der Lösung von Problemen mit Husqvarna OPERATORS MANUAL CS 2156C. Sie finden dort fast immer Troubleshooting, also die am häufigsten auftauchenden Störungen und Mängel bei Husqvarna OPERATORS MANUAL CS 2156C gemeinsam mit Hinweisen bezüglich der Arten ihrer Lösung. Sogar wenn es Ihnen nicht gelingen sollte das Problem alleine zu bewältigen, die Anleitung zeigt Ihnen die weitere Vorgehensweise – den Kontakt zur Kundenberatung oder dem naheliegenden Service.
