Benutzeranleitung / Produktwartung 6160EX des Produzenten Honeywell
Zur Seite of 18
Galant 6160EX Keypad User Instructions Honeywell Security.
Contents Glossary .....................................................................................3 Introduction ...............................................................................4 Day Mode, Full Setting and Unsetting ...............
Glossary The following terms will be used in this manual: Alarm: A panel detection circuit has been tripped. Cancel: The action of stopping an alarm condition. Keyfob: A remote control dev ice for setting and unsetting . Each fob will belong to a user.
Introduction Your Galant panel has various system functions, which can be accessed by one of three methods: • type a user code at a keypad • press a button on an RF keyfob or • present a keytag to a proximit y reader. The system can support up to 8 users.
Day Mode, Full Setting and Unsetting Day mode is the normal m ode for the system. In this state the dis play will be simi lar to that shown on the right, wi th the time and date. Galant V2 21-01-02 09:54 Full Setting the Sy stem To full set the system (keypad) 1.
Unsetting the System from any Set State To unset the system (key pad) 1. Proceed to the keypad via the approved route. A pulsed tone will indicate that the entry timer is counting down. 2. Type in your User Code at the ke ypad before the expiry of the entry time.
Part And Night Setting It is possible to s et the s ystem but leave certa in detectors sw itched off. This is useful, fo r example, at nig ht while the b edrooms are occupi ed, or when leaving pets with in the pr emises. Your installer can set up these detectors.
Cancelling Alarms If an alarm activ ation is in progress, whether the system is set or unset, proceed directly to the keypad and type in your User Code. This will cancel the alarm condition and th e display will show the source of the alar m. T ypically, this will be the detection zone that caused the alarm condition.
Viewing the Event Log The Galant alarm panel has an Event Log history that records every event which oc curs on the system. Th is includes setting, unsetting, alarm activations and fault conditions. To view the ev ent log: 1. Type in your User Code. 2.
Omitting Zones From the System. To allow flexibil ity, you can tem porarily disable i ndividual detection zones. This is called ‘Omitting’. Once a zone is omitted, it will be disabled for the duration of the next set period. When the panel is next unset, the zone will be enabled again.
Chime The Chime function allows you to set up a zone to cause a chim e tone to activate on the in ternal sounder and keypad, every time a particular zone is opened. This is particularly useful to warn if a door has b een opened. To set up a zone for Chime: 1.
Adding and Removing Keyfo bs. The Keyfobs used on this system employ high security KEELOQ TM Rolling Code Encr yption to make them virtually i mpossible to duplicate. Adding Keyfobs With the system in DAY mode at the keypad: 1. Enter master user code, 8 (CODE), and user number (1-8).
6. After second double b eep the card has been added successfully. Note: If at any time a triple bleep is heard, the learn procedure has failed. Removing Keytags Any keytag can be removed from the system as follows: 1. Enter master user code, 8 (CODE), and user number (1-8).
User Descriptors Each user code o n the system can ha ve a 6-character tag assigned. This tag or descriptor makes it easy to identify users who accessed the system when viewing the event log. User descriptors are entered in a s imilar way to entering SMS tex t messages on mobile phones.
Testing the System A test function is a vailable which allows a user to manual ly test the sensors and alarm sounders on the syst em. This test is carried out as follows: From normal Day mode; 1. Type in the user code. 2. Press 5 (Test) 3. The system will ring the outsid e bells for 5 seconds and switch on the strobe light.
System Indications In addition to the displays shown previously, the following fau lt displays may appear on the k eypad. I f the fault cannot be rectified, please contact your installer, explaini ng the exact detail on the dis play. Keypad Display Meaning Tamper ZN: xx A tamper fault has occurred on the zone shown.
Hotkeys Hotkeys are key com binations on the ke ypad that can cause an instant alarm condition. Both ke ys must be pressed sim ultaneously to activate the alarm.
Zone Information Zone Location Full Part Night 1 2 3 4 5 6 7 8 9 10 11 12 IU1-1233 Rev 1.3 18.
Ein wichtiger Punkt beim Kauf des Geräts Honeywell 6160EX (oder sogar vor seinem Kauf) ist das durchlesen seiner Bedienungsanleitung. Dies sollten wir wegen ein paar einfacher Gründe machen:
Wenn Sie Honeywell 6160EX noch nicht gekauft haben, ist jetzt ein guter Moment, um sich mit den grundliegenden Daten des Produkts bekannt zu machen. Schauen Sie zuerst die ersten Seiten der Anleitung durch, die Sie oben finden. Dort finden Sie die wichtigsten technischen Daten für Honeywell 6160EX - auf diese Weise prüfen Sie, ob das Gerät Ihren Wünschen entspricht. Wenn Sie tiefer in die Benutzeranleitung von Honeywell 6160EX reinschauen, lernen Sie alle zugänglichen Produktfunktionen kennen, sowie erhalten Informationen über die Nutzung. Die Informationen, die Sie über Honeywell 6160EX erhalten, werden Ihnen bestimmt bei der Kaufentscheidung helfen.
Wenn Sie aber schon Honeywell 6160EX besitzen, und noch keine Gelegenheit dazu hatten, die Bedienungsanleitung zu lesen, sollten Sie es aufgrund der oben beschriebenen Gründe machen. Sie erfahren dann, ob Sie die zugänglichen Funktionen richtig genutzt haben, aber auch, ob Sie keine Fehler begangen haben, die den Nutzungszeitraum von Honeywell 6160EX verkürzen könnten.
Jedoch ist die eine der wichtigsten Rollen, die eine Bedienungsanleitung für den Nutzer spielt, die Hilfe bei der Lösung von Problemen mit Honeywell 6160EX. Sie finden dort fast immer Troubleshooting, also die am häufigsten auftauchenden Störungen und Mängel bei Honeywell 6160EX gemeinsam mit Hinweisen bezüglich der Arten ihrer Lösung. Sogar wenn es Ihnen nicht gelingen sollte das Problem alleine zu bewältigen, die Anleitung zeigt Ihnen die weitere Vorgehensweise – den Kontakt zur Kundenberatung oder dem naheliegenden Service.