Benutzeranleitung / Produktwartung AS122XHERA des Produzenten Haier
Zur Seite of 33
W ALL MOUTED TYPE INDOOR UNITS AS072XHERA AS092XHERA AS122XHERA R410A MUL TI SPLIT SERIES ROOM AIR CONDITIONER OPERA TION & INST ALLA TION MANUAL No.0010577054 Please read this manual carefully before using this air conditioner . Please keep this manual safely for future use.
Contents Cautions ............................................................................................. Safety precautions............................................................................... Parts and Functions .....................
Cautions 1 Disposal of the old air conditioner Before disposing an old air conditioner that goes out of use, please make sure it's inoperative and safe. Unplug the air conditioner in order to avoid the risk of child entrapment. It must be noticed that air conditioner system contains refrigerants, which require specialized waste disposal.
4. The wiring method should be in line with the local wiring standard. 5. The power cable and connecting cable are self-provided. The requirement of the connecting cable: All the cables shall have got the Local authentication certificate.
3 W ARNING! Carefully r ead the following information in order to operate the air conditioner corr ectly . Below are listed three kinds of Safety Cautions and Suggestions. INSTRUCTIONS: These information can ensure the correct operation of the machine.
4 CAUTIONS! Conditioner should not be used for any other purpose other than air conditioning. Don't use air-conditioner for any other special purposes, e.g. the preservation and protection of food, animals, plants, pecision apparatus as well as work of art, otherwise the qualities of these stuffs may be damaged.
5 CAUTION ! Please ask the dealer or specialist to install, never try by the users themselves. After the installation please be sure of the following conditions. Safety pr ecautions Incorrect installation may cause water leaking, shock and fire hazard.
Parts and Functions 6 Front panel Air inlet grille Louver LED board INDOOR UNIT FRONT VIEW INDOOR UNIT BACK VIEW Signal receiver Mounting plate Heat preservation pipe Connecting pipes Drainage pipes *.
7 Parts and Functions REMOTE CONTROLLER MODE CLOCK Used to set correct time. TIMER LIGHT Used to set temp.,temp. range:16 C~30 C SLEEP Used to select sleep mode HOUR Used to set clock and timer setting. RESET Used to reset the controller back to normal condition.
8 MODE SLEEP SWING CLOCK TIMER SET LOCK LIGHT RESET STERILIZE 1 2 3 HEALTH AIRFLOW FRESH CODE Operation Clock set When unit is started for the first time and after replacing batteries in remote controller , clock should be adjusted as follows: Press CLOCK button, "AM"or "PM" flashes.
Operation Auto 2 1 Press ON/OFF button Unit starts running. The previous status appears on the display (except. TIMER, SLEEP mode) Press MODE button. For each press, operation mode changes as follows: 4 Remote controller Press ON/OFF button Unit stops running.
10 A Operation Cooling Press ON/OFF button Unit starts running. The previous status appears on the display (except. TIMER, SLEEP mode) Press MODE button. For each press, operation mode changes as follows: Select temp. button Press TEMP button Every time the button is pressed, temp.
1 1 A Operation Dry Press ON/OFF button Unit starts running. The previous status appears on the display (except. TIMER, SLEEP mode) Press MODE button. For each press, operation mode changes as follows: Select Drying operation shows" " Dry operation starts Select temp.
12 A Operation Fan Press ON/OFF button Unit starts running. The previous status appears on the display (except. TIMER, SLEEP mode) Press MODE button. For each press,operation mode changes as follows: Select Fan operation shows " ", Fan operation starts.
13 A Operation Heating Press ON/OFF button Unit starts running. The previous status appears on the display (except. TIMER, SLEEP mode) Press MODE button. For each press,operation mode changes as follows: Select Heating operation " " appears and Heating operation starts.
14 A Operation Air flow adjustment Swing louvers (V ertical louvers) Up and down Put louvers at up position in cooling and down position in heating mode. This will be helpful to keep an even room temp. Note: In cooling or dry operation, don't put horizontal louvers at downward position for a long time, or outlet grill might get frosted.
15 A Operation Sleep Remote control unit Usage of the Sleep function After starting, set the Run mode and press the Sleep button. Run mode 1. In cooling and dry After starting of the Sleep operation, the temperature will be raised for 1 C higher than the set temperature 1 hour later ,and be raised for 1 C after another hour .
16 A Operation T imer on/off operation Remote control unit TIMER operation Set Clock correctly before starting T imer operation (refer to page 2) Y ou can let unit start or stop automatically at following times: Before you wake up in the morning, or get back from outside or after you fall asleep at night.
17 A Operation T imer on-off function Remote controller operation TIMER ON-OFF (1) After unit start, select your desired operation mode. Operation mode will be displayed on LCD.
18 A Operation After turning on the unit and set the desired working mode. Press the Health button, the LCD will display " ", the unit begins health operation (start the negative ion generation device).
Notes for safety Clean the dust filter periodically: Blockage of the dust filter would reduce the cooling and heating effect, consume more power , water would be leaked during cooling, and other failures would also occur . 19 ! ! Use the fuse of required capacity: Never use steel wire or copper wire to take place of the fuse.
Operation and Maintenance 20 Emergency and T est Operation Use this operation only when the remote controller is defective or lost. When the emergency operation switch is pressed "Pi" sound is heard once, which means the start of this operation.
21 The followings are not malfuncition Hua Hua T r ouble shooting W ater flowing sound is heard When the air conditoner is started, when the compressor starts or stops during operation or when the air conditioner is stopped,it som- etimes sounds “ Bi- Bi-” or “Godo-Godo”.
22 **? ON OFF Air does not blow or the fan speed cannot be changed during drying. In DR Y mode, when room temperature becomes 2 C higher than temperature setting, unit rill run intermittently at LO speed regardless of F AN setting During heating,indoor fan is still running even unit is stopped.
23 Customer Need-to-know Customer Need-to-know Please install the air conditioner according to the requirements specified in this manual to ensure the air conditioner work well. Be careful not to scratch the surface of the case during moving the air conditioner .
24 W ARNING This system should be applied to places as office, restaurant, residence and the like. Application to inferior environment such as engineering shop could cause equipment malfunction. Please entrust installation to either the company which sold you the equipment or to a professional contractor .
25 PRECAUTION Self-contained accessories 3. Accessories for installation Name of Parts No. A B C D E F Non-adhesive T ape Adhesive tape Connecting Hose Gypsum powder Drain hose Heat insulation material 2.
5. Method for Cutting and Expanding Pipes. 26 Make a hole of 60mm in diameter , slightly descending to outside the wall. Install piping hole cover and seal it off with putty after installation. 4. Drawing of pipe Rear piping Draw pipes and the drain hose, then fasten them with the adhesive tape.
27 Heat insulation material Drain hose Piping Indoor/outdoor electric cable signal wire Change-f or -fresh-air tube Indoor/outdoor electric cord and drain hose must be bound with refrigerant piping by protecting tape 8. Indoor unit communication addr esses setting 1.
28 I. If you want to change the address, please repeat the above steps from E to G. J. After setting all the addresses, please power off the system and then power on again. Otherwise the system will not start to work. K. Once the addresses are successfully set, please do not change it any more to avoid confusion.
29 When tr ouble happens Insufficient cooling or heating The operation controller adjusted as required Air filter too dirty ? Horizontal swing louver upward ? (in HEA T mode) Any obstacle exists at th.
30 Failur e code Note: 1. Please contact the installers or distributors when trouble happens to repair it. 2. T urn the power off and power on again, if the failure code recurs, please change the indoor unit PCB. 3. Failrue codes maked with are resumable.
HAIER GROUP Qingdao Haier Air Conditioner Electric Co., Ltd. Address: Haier Garden, Qianwangang Road, Economic Development Zone, Qingdao, Shandong 266500, P .
Ein wichtiger Punkt beim Kauf des Geräts Haier AS122XHERA (oder sogar vor seinem Kauf) ist das durchlesen seiner Bedienungsanleitung. Dies sollten wir wegen ein paar einfacher Gründe machen:
Wenn Sie Haier AS122XHERA noch nicht gekauft haben, ist jetzt ein guter Moment, um sich mit den grundliegenden Daten des Produkts bekannt zu machen. Schauen Sie zuerst die ersten Seiten der Anleitung durch, die Sie oben finden. Dort finden Sie die wichtigsten technischen Daten für Haier AS122XHERA - auf diese Weise prüfen Sie, ob das Gerät Ihren Wünschen entspricht. Wenn Sie tiefer in die Benutzeranleitung von Haier AS122XHERA reinschauen, lernen Sie alle zugänglichen Produktfunktionen kennen, sowie erhalten Informationen über die Nutzung. Die Informationen, die Sie über Haier AS122XHERA erhalten, werden Ihnen bestimmt bei der Kaufentscheidung helfen.
Wenn Sie aber schon Haier AS122XHERA besitzen, und noch keine Gelegenheit dazu hatten, die Bedienungsanleitung zu lesen, sollten Sie es aufgrund der oben beschriebenen Gründe machen. Sie erfahren dann, ob Sie die zugänglichen Funktionen richtig genutzt haben, aber auch, ob Sie keine Fehler begangen haben, die den Nutzungszeitraum von Haier AS122XHERA verkürzen könnten.
Jedoch ist die eine der wichtigsten Rollen, die eine Bedienungsanleitung für den Nutzer spielt, die Hilfe bei der Lösung von Problemen mit Haier AS122XHERA. Sie finden dort fast immer Troubleshooting, also die am häufigsten auftauchenden Störungen und Mängel bei Haier AS122XHERA gemeinsam mit Hinweisen bezüglich der Arten ihrer Lösung. Sogar wenn es Ihnen nicht gelingen sollte das Problem alleine zu bewältigen, die Anleitung zeigt Ihnen die weitere Vorgehensweise – den Kontakt zur Kundenberatung oder dem naheliegenden Service.
