Benutzeranleitung / Produktwartung MA785GMT-UD2H des Produzenten Gigabyte
Zur Seite of 103
GA-MA785GPMT -UD2H/ GA-MA785GMT -UD2H/ GA-MA785GMT -US2H AM3 socket motherboard for AMD Phenom ™ II processor/ AMD Athlon ™ II processor User's Manual Rev .
Motherboard GA-MA785GPMT -UD2H/ GA-MA785GMT -UD2H/ GA-MA785GMT -US2H July 16, 2009 July 16, 2009 Motherboard GA-MA785GPMT-UD2H/GA-MA785GMT -UD2H/GA-MA785GMT-US2H.
Copyright © 2009 GIGA-BYTE TECHNOLOGY CO., L TD. All rights reserved. The trademarks mentioned in this manual are legally registered to their respective owners. Disclaimer Information in this manual is protected by copyright laws and is the property of GIGABYTE.
- 4 - T able of Contents Box Contents ................................................................................................................... 6 Optional Items ................................................................................
- 5 - Chapter 3 Drivers Installation ........................................................................................ 61 3-1 Installing Chipset Drivers ............................................................................... 61 3-2 Application Software .
- 6 - Box Contents GA-MA785GPMT -UD2H, GA-MA785GMT -UD2H, or GA-MA785GMT -US2H motherboard Motherboard driver disk User's Manual Quick Installation Guide One IDE cable T wo SA T A 3Gb/s cables I/O Shield Optional Items Floppy disk drive cable (Part No.
- 7 - GA-MA785GPMT -UD2H/GA-MA785GMT -UD2H(US2H) Motherboard Layout "*" The GA-MA785GPMT -UD2H/GA-MA785GMT-UD2H adopts All-Solid Capacitor design.
- 8 - Block Diagram AM3 CPU Hyper T ransport 3.0 AMD 785G PCIe CLK (100 MHz) PCI Express Bus CPU CLK+/- (200 MHz) 1 PCI Express x1 RTL81 1 1C DDR3 1666 (O.C.)/1333/1066 MHz PCIe CLK (100 MHz) 1 PCI Express x16 LAN RJ45 x1 GFX CLK (100 MHz) D-Sub DVI-D or HDMI (Note) PCI Express x16 j Only for GA-MA785GPMT -UD2H.
- 9 - Hardware Installation 1- 1 Installation Precautions Th e m ot her bo ar d c on ta in s n um er ou s d el ic at e e le ct ro ni c c ir cu it s a nd comp one nt s w hi ch can become damaged as a result of electrostatic discharge (ESD).
Hardware Installation - 10 - 1- 2 Product Specications CPU Support for AM3 processors: AMD Phenom ™ II processor/ AMD Athlon ™ II processor (Go to GIGABYTE's website for the latest CPU support list.
- 1 1 - Hardware Installation USB Integrated in the South Bridge Up to 12 USB 2.0/1.1 ports (6 on the back panel, 6 via the USB brackets connected to the internal USB headers) IEEE 1394 T .
Hardware Installation - 12 - (Note 1) Due to Windows Vista/XP 32-bit operating system limitation, when more than 4 GB of physical memory is installed, the actual memory size displayed will be less than 4 GB. (Note 2) The DVI-D port does not support D-Sub connection by adapter.
- 13 - Hardware Installation 1-3 Installing the CPU and C PU Cooler 1-3 -1 I nst all ing t he CPU A. Locate the pin one (denoted by a small triangle) of the CPU socket and the CPU. Read the following guidelines before you begin to install the CPU: • Make sure that the motherboard supports the CPU.
Hardware Installation - 14 - B. Follow the steps below to correctly install the CPU into the motherboard CPU socket. • Before installing the CPU, make sure to turn off the computer and unplug the power cord from the power outlet to prevent damage to the CPU.
- 15 - Hardware Installation 1-3 -2 I nst all ing t he CPU Cool er Follow the steps below to correctly install the CPU cooler on the CPU. (The following procedure uses the GIGABYTE cooler as the example.) Step 1: Apply an even and thin layer of thermal grease on the surface of the installed CPU.
Hardware Installation - 16 - 1- 4 Installin g the Me mor y DDR3_1 DDR3_2 DDR3_3 DDR3_4 Read the following guidelines before you begin to install the memory: • Make sure that the motherboard supports the memory . It is recommended that memory of the same capacity , brand, speed, and chips be used.
- 17 - Hardware Installation 1- 4 -2 Inst all ing a M emo r y Notch Before installing a memory module, make sure to turn off the computer and unplug the power cord from the power outlet to prevent damage to the memory module. DDR3 and DDR2 DIMMs are not compatible to each other or DDR DIMMs.
Hardware Installation - 18 - 1-5 Installing an Expansion Card Read the following guidelines before you begin to install an expansion card: • Make sure the motherboard supports the expansion card. Carefully read the manual that came with your expansion card.
- 19 - Hardware Installation 1-6 Setup of the A TI Hybrid CrossFire X ™ Conguration Combining the onboard GPU with a discrete graphics card, A TI Hybrid CrossFireX can provide signicantly advanced display performance for AMD platform. This section give instructions on conguring an A TI Hybrid CrossFireX system.
Hardware Installation - 20 - 1- 7 Back Panel Con nectors USB Port The USB port supports the USB 2.0/1.1 specication. Use this port for USB devices such as a USB key - board/mouse, USB printer , USB ash drive and etc. PS/2 Keyboard or PS/2 Mouse Port Use this port to connect a PS/2 keyboard or PS/2 mouse.
- 21 - Hardware Installation Activity LED: State Description Blinking Data transmission or receiving is occurring Off No dat a tra nsmi ssio n o r re ceiv ing is occu rri ng Connection/Speed LED: Stat.
Hardware Installation - 22 - Center/Subwoofer Speaker Out Jack (Orange) Use this audio jack to connect center/subwoofer speakers in a 5.1/7.1-channel audio conguration. Rear Speaker Out Jack (Black) Use this audio jack to connect rear speakers in a 4 kl /5.
- 23 - Hardware Installation 1-8 Internal Connec tors Read the following guidelines before connecting external devices: • First make sure your devices are compliant with the connectors you wish to connect. • Bef ore in stal ling t he de vice s, be s ure to turn o ff the de vice s and y our co mput er.
Hardware Installation - 24 - A TX_12V_2X4: A TX_12V_2X4 4 1 8 5 A TX: Pin No. Denition 13 3.3V 14 -12V 15 GND 16 PS_ON (soft On/Off) 17 GND 18 GND 19 GND 20 -5V 21 +5V 22 +5V 23 +5V (Only f or 2x12- pin A TX) 24 GND (Only for 2x12- pin A TX) Pin No.
- 25 - Hardware Installation 3/4) CPU_F AN/SYS_F AN (Fan Headers) The motherboard has a 4-pin CPU fan header (CPU_F AN)and a 4-pin system fan header(SYS_FAN). Each fan header supplies a +12V power voltage and possesses a foolproof insertion design. When con- necting a fan cable, be sure to connect it in the correct orientation.
Hardware Installation - 26 - 6) FDD (Floppy Disk Drive Connector) This connector is used to connect a oppy disk drive. The types of oppy disk drives supported are: 360 KB, 720 KB, 1.2 MB, 1.44 MB, and 2.88 MB. Before connecting a oppy disk drive, be sure to locate pin 1 of the connector and the oppy disk drive cable.
- 27 - Hardware Installation 8) SA T A2_0/1/2/3/4 (SA T A 3Gb/s Connectors) The SA T A connectors conform to SA T A 3Gb/s standard and are compatible with SAT A 1.5Gb/s standard. Each SA T A conn ector s upports a sing le SA T A device . The A MD S B710 c ontr oller s upports RAID 0, R AID 1, RAID 10, and JBOD.
Hardware Installation - 28 - 10) F_P ANEL (Front Panel Header) Connect the power switch, reset switch, speaker and system status indicator on the chassis front panel to this header according to the pin assignments below . Note the positive and negative pins before con- necting the cables.
- 29 - Hardware Installation 1 1) F_AUDIO (Front Panel Audio Header) The front panel audio header supports Intel High Denition audio (HD) an d AC'97 audio. Y ou may connect your chassis front panel audio module to this header. Make sure the wire assignments of the module con - nector match the pin assignments of the motherboard header.
Hardware Installation - 30 - 13) SPDIF_IO (S/PDIF In/Out Header) This header supports digital S/PDIF In/Out. Via an optional S/PDIF In and Out cable, this header can connect to an audio device that supports digital audio out and an audio system that supports digital au- dio in.
- 31 - Hardware Installation 15) F_1394_1 (IEEE 1394a Header) The header conforms to IEEE 1394a specication. The IEEE 1394a header can provide one IEEE 1394a port via an optional IEEE 1394a bracket. For purchasing the optional IEEE 1394a bracket, please con- tact the local dealer .
Hardware Installation - 32 - 18) CI (Chassis Intrusion Header) This motherboard provides a chassis detection feature that detects if the chassis cover has been re- moved. This function requires a chassis with chassis intrusion detection design. 17) COM (Serial Port Header) The COM header can provide one serial port via an optional COM port cable.
- 33 - Hardware Installation 19) CLR_CMOS (Clearing CMOS Jumper) Use this jumper to clear the CMOS values (e.g. date information and BIOS congurations) and reset the CMOS values to factory defaults.
Hardware Installation - 34 -.
- 35 - BIOS Setup BIOS (Ba sic Inpu t and Out put Syst em) reco rds hard ware par ameters of the sy stem in t he CMOS o n the motherboard. Its major functions include conducting the Power-On Self-T est (POST) during system startup, saving sy stem param eters and l oading op erating sy stem, etc .
BIOS Setup - 36 - 2-1 Startup Screen The following screens may appear when the computer boots. Function Keys: <DEL>: BIOS SETUP Press the <Delete> key to enter BIOS Setup or to access the Q-Flash utility in BIOS Setup.
- 37 - BIOS Setup 2-2 The Main Menu Once you enter the BIOS Setup program, the Main Menu (as shown below) appears on the screen. Use ar- row keys to move among the items and press <Enter> to accept or enter a sub-menu.
BIOS Setup - 38 - The Functions of the <F1 1> and <F12> keys (For the Main Menu Only) F1 1: Save CMOS to BIOS This function allows you to save the current BIOS settings to a prole. Y ou can create up to 8 proles (Prole 1-8) and name each prole.
- 39 - BIOS Setup 2-3 MB Intelligent T weaker(M.I.T .) • Whether the system will work stably with the overclock/overvoltage settings you made is depen - dent on your overall system congurations. Incorrectly doing overclock/overvoltage may result in damage to CPU, chipset, or memory and reduce the useful life of these components.
BIOS Setup - 40 - CMOS Setup Utility-Copyright (C) 1984-2009 A ward Software Advanced Clock Calibration higf : Move Enter: Select +/-/PU/PD: V alue F10: Save ESC: Exit F1: General Help F5: Previous V .
- 41 - BIOS Setup CPU Clock Ratio Allows you to alter the clock ratio for the installed CPU. The adjustable range is dependent on the CPU being used. CPU NorthBridge Freq. Allows you to alter the North Bridge controller frequency for the installed CPU.
BIOS Setup - 42 - DCT s Mode Allows you to set memory control mode. Ganged Sets memory control mode to single dual-channel. Unganged Sets memory control mode to two single-channel. (Default) DDR3 Timing Items Manual allows all DDR3 Timing items below to be congurable.
- 43 - BIOS Setup T rfc3 for DIMM4 Options are: Auto (default), 90ns, 1 10ns, 160ns, 300ns, 350ns. Write Recovery Time Options are: Auto (default), 5T~8T , 10T , 12T . Precharge Time Options are: Auto (default), 4T~7T . Row Cycle Time Options are: Auto (default), 1 1T~42T .
BIOS Setup - 44 - CPU NB VID Control Allows you to set the CPU Northbridge VID voltage. Auto sets the CPU Northbridge VID voltage as re- quired. The adjustable range is dependent on the CPU being installed. (Default: Normal) Note: Increasing CPU voltage may result in damage to your CPU or reduce the useful life of the CPU.
- 45 - BIOS Setup Date (mm:dd:yy) Sets the system date. The date format is week (read-only), month, date and year . Select the desired eld and use the up arrow or down arrow key to set the date. Time (hh:mm:ss) Sets the system time. For example, 1 p.
BIOS Setup - 46 - The following elds display your hard drive specications. If you wish to enter the parameters manually , refer to the information on the hard drive. Capacity Approximate capacity of the currently installed hard drive. Cylinder Number of cylinders.
- 47 - BIOS Setup 2-5 Advanced BIOS Features Internal Graphics Mode j Allows you to determine whether to allocate the system memory for the onboard graphics controller . UMA Allocates memory for the onboard graphics controller from the system memory .
BIOS Setup - 48 - Onboard VGA output connect Species the graphics display of the onboard VGA output from the D-SUB/DVI-D or D-SUB/HDMI. Auto Lets the BIOS automatically determines the primary display port for output, depending on to which port the display device is connected, D-SUB/DVI-D or D-SUB/HDMI.
- 49 - BIOS Setup Away Mode Enables or disables Away Mode in Windows XP Media Center operating system. Away Mode allows the system to silently perform unattended tasks while in a low-power mode that appears off. (Default: Disabled) Backup BIOS Image to HDD Allows the system to copy the BIOS image le to the hard drive.
BIOS Setup - 50 - 2-6 Integrated Peripherals OnChip IDE Channel Enables or disables the integrated IDE controller . (Default: Enabled) OnChip SA T A Controller Enables or disables the integrated SA T A controller .
- 51 - BIOS Setup This motherboard incorporates cable diagnostic feature designed to detect the status of the attached LAN cable. This feature will detect cabling issue and report the approximate distance to the fault or short. Refer to the following information for diagnosing your LAN cable: When No LAN Cable Is Attached.
BIOS Setup - 52 - Onboard Audio Function Enables or disables the onboard audio function. (Default: Enabled) If you wish to install a 3rd party add-in audio card instead of using the onboard audio, set this item to Disabled . Onboard 1394 Function Enables or disables the onboard IEEE 1394 function.
- 53 - BIOS Setup ACPI Suspend T ype Species the ACPI sleep state when the system enters suspend. S1(POS) Enables the system to enter the ACPI S1 (Power on Suspend) sleep state. In S1 sleep state, the system appears suspended and stays in a low power mode.
BIOS Setup - 54 - (Note) Supported on Windows Vista operating system only . PME Event Wake Up Allows the system to be awakened from an ACPI sleep state by a wake-up signal from a PCI or PCIe de- vice. Note: T o use this function, you need an A TX power supply providing at least 1A on the +5VSB lead.
- 55 - BIOS Setup PCI1 IRQ Assignment Auto BIOS auto-assigns IRQ to the rst PCI slot. (Default) 3,4,5,7,9,10,1 1,12,14,15 Assigns IRQ 3,4,5,7,9,10,1 1,12,14,15 to the rst PCI slot. PCI2 IRQ Assignment Auto BIOS auto-assigns IRQ to the second PCI slot.
BIOS Setup - 56 - Hardware Thermal Control Enables or disables the CPU overheating protection function. When enabled, the CPU core voltage and ratio will be reduced when the CPU is overheated. (Default: Enabled) Reset Case Open Status Keeps or clears the record of previous chassis intrusion status.
- 57 - BIOS Setup CPU Smart F AN Control Enables or disables the CPU fan speed control function. Enabled allows the CPU fan to run at different speed according to the CPU temperature. Y ou can adjust the fan speed with EasyTune based on system requirements.
BIOS Setup - 58 - Press <Enter> on this item and then press the <Y> key to load the safest BIOS default settings. In case system instability occurs, you may try to load Fail-Safe defaults, which are the safest and most stable BIOS settings for the motherboard.
- 59 - BIOS Setup Press <Enter> on this item and type the password with up to 8 characters and then press <Enter>. Y ou will be requested to conrm the password.
BIOS Setup - 60 - Press <Enter> on this item and press the <Y> key . This saves the changes to the CMOS and exits the BIOS Setup program. Press <N> or <Esc> to return to the BIOS Setup Main Menu. 2-13 Save & Exit Setup Press <Enter> on this item and press the <Y> key.
- 61 - Drivers Installation 3-1 Installing Chipset Drivers Chapter 3 Drivers Installation After inserting the driver disk, "Xpress Install" will automatically scan your system and then list all the drivers that are recommended to install.
Drivers Installation - 62 - 3-2 Application Software This page displays all the utilities and applications that GIGABYTE develops and some free software.
- 63 - Drivers Installation 3-4 Contact For the detailed contact information of the GIGABYTE T aiwan headquarter or worldwide branch ofces, click the URL on this page to link to the GIGABYTE website. 3-5 System This page provides the basic system information.
Drivers Installation - 64 - 3-6 Download Center T o update the BI OS, drivers, or application s, click the Download Center button to link to the GIGABYTE website.
- 65 - Unique Features 4-1 Xpress Recovery2 Chapter 4 Unique Features Xp r es s R e co v er y 2 i s a u ti l it y t h at a l l ow s y ou to q u i ck l y co m p re s s a nd back up your system data and perform restoration of it.
Unique Features - 66 - Step 3: Wh e n pa r ti t io n in g y o ur h a rd d r i ve , m ak e s ur e t o leave unallocated space (10 GB or more is recom- mended; actual size requirements vary , depending on the amount of data) and begin the installation of the operating system.
- 67 - Unique Features D. Using the Restore Function in Xpress Recovery2 E. Removing the Backup F . Exiting Xpress Recovery2 Sel ec t RESTORE to re st or e th e ba ck up t o yo ur h ar d dr ive in case the system breaks down. The RESTORE option will not be present if no backup is created before.
Unique Features - 68 - 4-2 BIOS Update Utilities GI GA B YT E m ot h er b oa r ds p r ov i de t w o un i qu e B IO S u pd a te t o ol s , Q- F la s h ™ an d @ BI O S ™ . GI G AB Y TE Q-Flash and @BIOS are easy-to-use and allow you to update the BIOS without the need to enter MS-DOS mod e.
- 69 - Unique Features B. Updating the BIOS When updatin g the BIOS, ch oose the loc ation where t he BIOS le is saved. The follow ing procedur e as - sumes that you save the BIOS le to a oppy disk. Step 1: 1. Insert the oppy disk containing the BIOS le into the oppy disk driv e.
Unique Features - 70 - Step 4: Press <Esc> and then <Enter> to exit Q-Flash and reboot the system. As the system boots, you should see the new BIOS version is present on the POST screen. Step 5: During the POST , press <Delete> to enter BIOS Setup.
- 71 - Unique Features 4-2-2 Updating the BIOS with the @BIOS Utility A. Before Y ou Begin 1. In Windows, close all applications and TSR (T erminate and Stay Resident) programs.
Unique Features - 72 - Available functions in EasyTune 6 may differ by motherboard model. Grayed-out area(s) indicates that the item is not congurable or the function is not supported.
- 73 - Unique Features 4-4 Easy Energy Saver GIGABYTE Easy Energy Saver is a revolutionary technology that delivers unparalleled power savings with a click of the button.
Unique Features - 74 - C. Stealth Mode In Stealth Mode, the system continues t o work with the user-dened power saving settings, even after the system is restarted. Re-enter the application only if you want to make any changes or completely close the application.
- 75 - Unique Features 4-5 Q-Share Q-Share is an easy and convenient data sharing too l. After conguring your LAN connection settings and Q-Share, you are able to share your data with computers on the same network, making full use of Internet resources.
Unique Features - 76 - 4-6 Time Repair Based on the Microsoft Volume Shadow Copy Services technology, Time Repair allows you to quickly back up and restore your system data in the Windows Vista operating system. Time Repair supports NTFS le system and can restore system data on P A T A and SA T A hard drives.
- 77 - Appendix Chapter 5 Appendix 5-1 Conguring SA T A Hard Drive(s) T o congure SA T A hard drive(s), follow the steps below: A. Install SA T A hard drive(s) in your computer . B. Congure SA T A controller mode in BIOS Setup. C. Congure a RAID array in RAID BIOS.
Appendix - 78 - B. Conguring SA T A controller mode in BIOS Setup Make sure to congure the SA T A controller mode correctly in system BIOS Setup. Step 1: Turn on your com puter an d press < Delete> to enter BIOS Set up duri ng the POS T (Power-O n Self-T est).
- 79 - Appendix C. Conguring RAID set in RAID BIOS Enter the RAID BIOS setup utility to congure a RAID array . Skip this step and proceed with the installation of Windows operating system for a non-RAID conguration.
Appendix - 80 - Create Arrays Manually T o create a new array , press <2> to enter the Dene LD Menu window (Figure 4). The Dene LD selection from the Main Menu allows users to begin the process of manually dening the drive elements and RAID levels for one or multiple disk arrays.
- 81 - Appendix In the following procedure, we'll create RAID 0 as an example. 1. Under the RAID Mode section, press the <SP ACE> key to select RAID 0 . 2. Set the Stripe Block size. 64 KB is the default. 3. Under the Drives Assignments section, press the up or down arrow key to highlight a drive.
Appendix - 82 - Delete an Array The Delete Array menu option allows for deletion of disk array assignments. Deleting an existing disk array could result in loss of data. Record all array information including the array type, the disk members, and stripe block size in case you wish to undo a deletion.
- 83 - Appendix 5-1-2 Making a SA T A RAID/AHCI Driver Diskette (Required for AHCI and RAID Mode) T o successfully install operating system onto SA T A hard drive(s) that is/are congured to RAID/AHCI mode, you need to install the SA T A controller driver during the OS installation.
Appendix - 84 - 5-1-3 Installing the SA T A RAID/AHCI Driver and Operating System With the SA T A RAID/AHCI driver diskette and correct BIOS settings, you are ready to install Windows Vista/ XP onto your hard drive(s). The followings are examples of Windows XP and Vista installation.
- 85 - Appendix B. Installing Windows Vista (The procedure below assumes that only one RAID array exists in your system.) Step 1: Restart your system to boot from the Windows Vista setup disk and perform standard OS installation steps.
Appendix - 86 - Step 3: When a screen as shown in Figure 5 appears, select AMD AHCI Compatible RAID Controller and press Next . Step 4: After the driver is loaded, the RAID drive will appear . Select the RAID drive and then press Next to continue the OS installation (Figure 6).
- 87 - Appendix Rebuilding an Array: Rebuilding is the process of restoring data to a hard drive from other drives in the array . Rebuilding applies only to fault-tolerant arrays such as RAID 1, RAID 5, or RAID 10 arrays. T o replace the old drive, make sure to use a new drive of equal or greater capacity .
Appendix - 88 - 5-2-1 Conguring 2/4/5.1/7.1-Channel Audio The motherboard provides six audi o jacks on the b ack pan el w hi ch s upp or t 2/ 4/ 5.1 /7 .1 -ch an ne l (Note) au dio . The picture to the right shows the default audio jack assignments.
- 89 - Appendix Step 2: Connect an audio device to an audio jack. The The cur- rent connected device is dialog box appears. Select the device according to the type of device you connect. Then click OK . Step 3: On the Speakers s creen, click t he Spe aker Co ngur a - tion tab.
Appendix - 90 - 5-2-2 Conguring S/PDIF In/Out The S/PDIF In and Out cable (optional) provides S/PDIF In and S/PDIF Out functionalities. (Note) The actual locations of the SPDIF In and SPDIF Out connectors may differ by model.
- 91 - Appendix C. Conguring S/PDIF Out: The S/PDIF Out jacks can transmit audio signals to an external decoder for decoding to get the best audio quality .
Appendix - 92 - 5-2-3 Enabling the Dolby Home Theater Function jk Before D olby Hom e Theater is enabled , you get only 2-c hannel p laybac k output (from th e front speakers) when playing 2-channel stereo sources. Y ou must play 4-, 5.1-, or 7.1- chan- nel content to get 4-, 5.
- 93 - Appendix 5-2-4 Conguring Microphone Recording Step 1: After installing the audio driver , the HD Audio Manager icon will appear in the notication area.
Appendix - 94 - Step 4: T o r ai s e t h e r e c o rd i n g a n d p l a yb a c k v o l um e f o r t h e microphone, click the Microphone Boost icon on the right of the Recor ding V olume slider and set the Microphone Boost level.
- 95 - Appendix Step 3: When the Stereo Mix item appears, right-click on this item and select Enable . Then set it as the default de- vice. Step 4: Now you can access the HD Audio Manager to cong - ure Stereo Mix and use Sound Recorder to record the sound.
Appendix - 96 - 5-3 T roubleshooting 5-3-1 Frequently Asked Questions T o read more FAQs for your motherboard, please go to the Support&DownloadsMotherboardF AQ page on GIGABYTE's website. Q: In the BIOS Setup program, why are some BIOS options missing? A: Some advanced options are hidden in the BIOS Setup program.
- 97 - Appendix 5-3-2 T roubleshooting Procedure If you encounter any troubles during system startup, follow the troubleshooting procedure below to solve the problem. ST ART A Turn off the power . Remove all peripherals, connecting cables, and power cord etc.
Appendix - 98 - The power supply , CPU or CPU socket might fail. The keyboard or keyboard connector might fail. END A Turn off the computer . Plug in the keyboard and mouse and restart the computer . The graphics card, expansion slot, or monitor might fail.
- 99 - Appendix 5-4 Regulatory Statements Regulatory Notices This document must not be copied without our writt en permission, and the con tents there of must not be imparted to a third party nor be used for any unauthorized purpose. Contravention will be prosecuted.
Appendix - 100 - Finally , we suggest that you practice other environmentally friendly actions by understanding and using the energy-saving features of this product (where applicable), recycling the inner and outer packaging (including shipping containers) this product was delivered in, and by disposing of or recycling used batteries properly .
- 101 - Appendix.
Appendix - 102 -.
- 103 - Appendix Contact Us • GIGA-BYTE TECHNOLOGY CO., L TD. Address: No.6, Bau Chiang Road, Hsin-Tien, T aipei 231, T aiwan TEL: +886-2-8912-4000 F AX: +886-2-8912-4003 T ech. and Non-T ech. Support (Sales/Marketing) : http://ggts.gigabyte.com.tw WEB address (English): http://www .
Ein wichtiger Punkt beim Kauf des Geräts Gigabyte MA785GMT-UD2H (oder sogar vor seinem Kauf) ist das durchlesen seiner Bedienungsanleitung. Dies sollten wir wegen ein paar einfacher Gründe machen:
Wenn Sie Gigabyte MA785GMT-UD2H noch nicht gekauft haben, ist jetzt ein guter Moment, um sich mit den grundliegenden Daten des Produkts bekannt zu machen. Schauen Sie zuerst die ersten Seiten der Anleitung durch, die Sie oben finden. Dort finden Sie die wichtigsten technischen Daten für Gigabyte MA785GMT-UD2H - auf diese Weise prüfen Sie, ob das Gerät Ihren Wünschen entspricht. Wenn Sie tiefer in die Benutzeranleitung von Gigabyte MA785GMT-UD2H reinschauen, lernen Sie alle zugänglichen Produktfunktionen kennen, sowie erhalten Informationen über die Nutzung. Die Informationen, die Sie über Gigabyte MA785GMT-UD2H erhalten, werden Ihnen bestimmt bei der Kaufentscheidung helfen.
Wenn Sie aber schon Gigabyte MA785GMT-UD2H besitzen, und noch keine Gelegenheit dazu hatten, die Bedienungsanleitung zu lesen, sollten Sie es aufgrund der oben beschriebenen Gründe machen. Sie erfahren dann, ob Sie die zugänglichen Funktionen richtig genutzt haben, aber auch, ob Sie keine Fehler begangen haben, die den Nutzungszeitraum von Gigabyte MA785GMT-UD2H verkürzen könnten.
Jedoch ist die eine der wichtigsten Rollen, die eine Bedienungsanleitung für den Nutzer spielt, die Hilfe bei der Lösung von Problemen mit Gigabyte MA785GMT-UD2H. Sie finden dort fast immer Troubleshooting, also die am häufigsten auftauchenden Störungen und Mängel bei Gigabyte MA785GMT-UD2H gemeinsam mit Hinweisen bezüglich der Arten ihrer Lösung. Sogar wenn es Ihnen nicht gelingen sollte das Problem alleine zu bewältigen, die Anleitung zeigt Ihnen die weitere Vorgehensweise – den Kontakt zur Kundenberatung oder dem naheliegenden Service.
