Benutzeranleitung / Produktwartung ETR-30N des Produzenten Furuno
Zur Seite of 48
NETW ORK SOUNDER ETR-30N Back.
i SAFETY INSTR UCTIONS WARNING Turn off the power at the switchboard before beginning the installation. Fire or electrical shock can result if the power is left on. Do not install the equipment where it may get wet from rain or water splash. Water in the equipment can result in fire, electrical shock or damage to the equipment.
ii The transducer cable must be handled carefully, following the guidelines below. • Keep fuels and oils away from the cable. • Locate the cable where it will not be damaged. • The cable sheath is made of chloro- phrene or polychloride vinyl, which is easily damaged by plastic solvents such as toulene.
iii T A BL E OF CO NTE NTS SYSTEM CONFIGUR A TION ................................................................................ iv EQUIPMENT LIST S ............................................................................................. vi 1. MOUNTING .
iv SYSTEM CONFIGURA TION Single network sounder : Standard : Option : Local Supply T ransducer T ransducer High Freq. * = By using a hub, one NavNet series radar and three NavNet display units may be connected.
v Multipl e networ k s ounder s Network Sounder ETR-30N NavNet Radar Display Unit NavNet Display Unit : Standard : Optional Supply : Local Supply HUB*1 NavNet Series *1 = By using a hub, one NavNet series radar and two NavNet display units may be connected.
vi EQUIPMENT LISTS S t andard s upply Name T ype Code No. Qty Remarks Network Sounder ETR-30N — 1 S pare Parts* SP02-04601 002-180-150 1 set CP02-07100 ( w/N avN et connection cable) — • Power C.
vii A vailable transducers 1kW transd u cer Freq. (kHz) Ship T ransducer Thru-hul l pipe T ank S teel — — FRP 28F-8 (000-015-00 3) 50B-6 (000-0 15-0 42) 50B-6B (000-015-04 3, 15 M) (000-015-018, 3.
viii 1kW transd u cer (con’t) Freq. (kHz) Ship T ransducer Thru-hul l pipe T ank S teel — — FRP 50B-6 (000-0 15-0 42) 50B-6B (000-015-04 3, 15 M) (000-015-018, 30M) (000-015-255, 40M) 200B-5S ( .
ix 2kW transd u cer Freq. (kHz) Ship T ransducer Thru- hull pipe T ank St e el TFB-7000 (2) (000-015-209) T -634 (000-015-810) 28/50 FRP 28F-18 (000- 015-0 04, 15M) (000-138-573, 30M) 50B-12 (000- 015.
x 3kW transd u cer Freq. (kHz) Ship T ransducer Thru-hull pipe T ank St e el — — 28/45 FR P 28F-24H (000-0 15-0 75) 45F-12H (000-0 15-0 76) — — St e el TFB-7000 (2) (000-015-209) T -681 (000-0.
xi 3kW transd u cer (con’t) Freq. (kHz) Ship T ransducer Thru-hull pipe T ank St e el TFB-7000 (2) (000-015-209) T -683 (000-015-853) 50/150 FRP 50F-24H (000-1 38-5 82) 150B-12H (00 0-015-074) TRB-1.
xii 1kW/2kW tran sducer Output (W) Freq. (kHz) Ship T ransducer Thru-hull pipe T ank S teel — — 28/50 FRP 28F-8 (000-015-00 3) 50B-12 (000- 015-020) — — S teel — — 28/68 FRP 28F-8 (000-015.
xiii 1kW/2kW tran sducer (con’t) Output (W) Freq. (kHz) Ship T ransducer Thru-hull pipe T ank St e el TFB-7000 (2) (000-015-209) T -638 (000-015-818) 50/200 FRP 50F-8G (000-015-066) 200B-8 (000- 015.
xiv 1kW/3kW tran sducer (con’t) Output (W) Freq. (kHz) Ship T ransducer Thru-hull pipe T ank S teel — — 50/88 FRP 50F-8G (000-015-066) 88F-126H (00 0-015-068) — — S teel — — FRP 50B-6 (0.
xv 1kW/3kW tran sd ucer (con’t) Output (W) Freq. (kHz) Ship T ransducer Thru-hull pipe T ank S teel — — 68/200 FRP 68F-8H (000-015-067) 200B-12H (00 0-015-069) — — S teel — — 88/150 FRP .
xvi 2kW/3kW tran sducer Output (W) Freq. (kHz) Ship T ransducer Thru-hull pipe T ank S teel — — 28/45 FRP 28F-18 (000- 015-0 04, 15M) (000-138-573, 30M) 45F-12H (000-0 15-0 76) — — S teel — .
xvii 3kW/2kW tran sducer (con’t) Output (W) Freq. (kHz) Ship T ransducer Thru-hull pipe T ank S teel — — 28/50 FRP 28F-24H (000-0 15-0 75) 50B-12 (000- 015-020) — — S teel — — 28/68 FRP .
1 1. MOUNTING 1.1 Net w ork S ounder 1.1.1 Mounti ng considerations The net work sounder c an be installe d on the deck or on the bulkhead. W hen selecting a mount ing locat ion, keep the following points in m ind: • The tem perature and humidity of the m ounting location should be m oderate and stable.
2 1.1.3 S tack ing unit s Y ou m ay stack t wo network sounders b y using t he optional pigg yback m ount kit (T ype OP02-84, Code No. 00 2-186-170) as below . Note: Chang e the tap setting on the lo wer unit before installing the upper unit . See paragraph 2.
3 2. WIRING , SETUP 2.1 Wiring 2.1.1 S tandard inst allation Connect NavNet series displa y un it or HUB, transducer , power cable and ground wire as below .
4 T ransducer Route the transducer ca ble well away from po wer cables, tele v isio ns and CR T s to prevent interference t o the network sounder . Attach the NCS connector t o t he t ransducer cable as below and connect it to the appropriate T RANSDUCER connector on the f r ont o f t he network sounder .
5 Multipl e networ k s ounder s Network Sounder ETR-30N NavNet Display Unit HUB NavNet Series *1 = By using a hub, one NavNet series radar and two NavNet display units may be connected.
6 2.2 Settings for S ingle Net work Sounder WARNING ELECTRICAL SHOCK HAZARD Do not open the equipment. Only qualified personnel should work inside the equipment. 2. 2.1 I nte rnal sett ing s Set t he tap i ns i de the netw ork sounder t o match transduc er o utput pow er .
7 FURUNO NETWORK SOUNDER ETR-30N HOST NAME TX/STBY POWER ON OFF I O 0 1 2 3 4 5 6 8 7 9 DEF AUL T LED lamp The lamp flashes when the NavNet displa y unit is powered and comm unicating with the network sounder . POWER switch Turns power On and off. HOST NAME Control Sets host name.
8 Note: T he v er y first time the system is pow ere d yo u a re asked if you want to start the simulation m ode, w h ich provides simulat ed operation of the equipm ent. Press the [CLEAR] key to start norm al operation to set up the transducer . F or f urther details about the sim ulation mode, see your NavNet series operator ’s manual.
9 2.2.3 T ransducer setup Enter transducer setting correctly. A wrong transducer setting can damage the transducer. CAUTION T ran sd ucer connected to the ET R-30 N i s p rogrammed in the ETR-30N 1. At the installat ion m enu, press the NETWORK SOUNDER SETUP soft key .
10 SNDR SETUP EDIT RETURN TRANSDUCER SETUP MANUAL HIGH FREQUENCY --kHz (0kW T AP:-) LOW FREQUENCY --kHz (0kW T AP:-) TAP SETTINGS MUST BE MADE ON ETR UNIT. AFTER SETUP, DISPLAY MUST BE TURNED OFF & ON TO ALLOW NEW SETTINGS TO TAKE EFFECT. Frequency setup scree n 3.
11 T ran sd ucer connected to the ET R-30 N i s n ot p ro grammed in the ETR-30N For the transducer not programmed in the ETR-30N, enter its f r equency m anually as below . Do not enter transducer specifications manually if the transducer is programmed in the equipment.
12 2.3 Settings f or T w o Netw ork Sounders 2.3.1 T wo ETR-30N netw ork sounders W hen installing two ETR-30N set the HOST NAM E cont rol t o “0” for the No. 1 ETR-30N and “1” for the No. 2 ETR-30 N. T urn the ETR-30N off and on again after sett ing t he HOST NAME control to register sett ings.
13 Note: The sam e IP address cannot be used when installing tw o ETR-30N or ET R-6/10N. T o change IP address and host nam e, set a diff erent number (1-9) f or each netw ork sounder with the HOST NAME sw it ch on t he ETR-30N. Note howev er t hat the ETR-6/10N’s host nam e and I P address are “SOUNDER” and “172.
14 2.3.2 ETR-30N and ETR-6/10N W hen installing an ETR-30N and an ET R-6/10N, the ETR-6/10N’s host nam e of SOUNDER cannot be changed. For t his reason, t he set the HOST NAME control of the ETR-30N to “1” and its host nam e to “SOUNDER1.” Turn the ETR-30N off and on again af ter setting the HOST NAME control to register set tings.
15 2.4 Erasing T ransdu cer Sett ing W h en changing tr ansdu cer(s), erase previous transducer setting(s) as sho wn belo w an d then enter new transdu cer settings as in paragraph 2.2. (The set cannot tr ansm it unless transducer settings are ent ered.
16 3. OPERATION, MAINTENANCE WARNING ELECTRICAL SHOCK HAZARD Do not open the equipment. Only qualified personnel should work inside the equipment. 3.1 Contro ls FURUNO NETWORK SOUNDER ETR-30N HOST NAM.
17 3.2 A ddi tio n s to Na v Net Ser i es O perator ’ s Manual Depending on t he vers ion number of your NavNet series operat or ’ s manual, its echo sounder descriptions m ay not match the screens you see. Please a dd the following descriptions to your m anual if they are not already present .
18 FREQ. A DJ Adjusts transm itting f r equenc y to suppress inte rference when it cannot be suppresse d w it h the interf erence rejector alone. T ARGET ECHO Sets fishing objective. Choose NO RMA L f or general fishing; SURF ACE for detecting surface f ish.
19 3.4 A ll Clear W h en t he sounder pict ure appears t o be abnorm al, execute t he “all cle ar” function from the ETR-30N to try to rest ore norm al operation. All clear erases all t ransducer settings, so reenter them ref erring to paragraph 2.
20 T h i s page i s intent ional ly lef t blank ..
A P-1 A PP ENDIX NE W BL T TR A NS DUCERS A ne w t y pe BL T transduc er ( B ol t-c l amp Lange vi n T ransducer) has be en de velope d for t his echo so under . T he BL T transducer has l arge b a ndw idt h, good sound ef fici ency , compact str uc t ure and is rei nforc ed f or prote cti on against slammi ng.
A P-2 S teel T-682 (000-015- 851) TW B - 6000 ( 2) (000-015- 207) T F B-7000 (2) (000-015- 209) 50/88 50BL- 24HR/88-126H FRP T -682F (000-015- 852) T RB-1 100 ( 2) (000-015- 219) - S teel T-683 (000-0.
SP - 1 E2027S01A SPECIFICA TI O NS OF NETWORK SOUNDER ETR-30N 1 GENERA L 1.1 Transmit Method Dual frequencies transmitting 1.2 Output Power 1/2/3 kW rms, selectable 1.3 Frequency 28.8-200 kHz, automatic sy nt hesiz er 1.4 Gain 0 dB µ V, S/N 10 dB or more 1.
ＰＡＣＫＩＮＧ ＬＩＳＴ ＰＡＣＫＩＮＧ ＬＩＳＴ ＰＡＣＫＩＮＧ ＬＩＳＴ ＰＡＣＫＩＮＧ ＬＩＳＴ 02FR-X-9852 -2 ETR-30N-E/J － N ETR-30N-E/J － N E.
ＰＡＣＫＩＮＧ ＬＩＳＴ ＰＡＣＫＩＮＧ ＬＩＳＴ ＰＡＣＫＩＮＧ ＬＩＳＴ ＰＡＣＫＩＮＧ ＬＩＳＴ 02FR-X-985 1 -3 ETR-30N-E/J-A ETR-30N-E/J-A ETR-30N-.
D - 1.
D - 2.
S - 1.
.
Your Local Agent/Dealer Your Local Agent/Dealer 9-52 Ashihara-cho, 9-52 Ashihara-cho, Nishinomi y a, Ja p an Nishinomi y a, Ja p an Tele p hone : Tele p hone : 0798-65-2111 0798-65-2111 fa x fa x 0798-65-4200 0798-65-4200 : : F IRST EDITION : F IRST EDITION : A UG.
Ein wichtiger Punkt beim Kauf des Geräts Furuno ETR-30N (oder sogar vor seinem Kauf) ist das durchlesen seiner Bedienungsanleitung. Dies sollten wir wegen ein paar einfacher Gründe machen:
Wenn Sie Furuno ETR-30N noch nicht gekauft haben, ist jetzt ein guter Moment, um sich mit den grundliegenden Daten des Produkts bekannt zu machen. Schauen Sie zuerst die ersten Seiten der Anleitung durch, die Sie oben finden. Dort finden Sie die wichtigsten technischen Daten für Furuno ETR-30N - auf diese Weise prüfen Sie, ob das Gerät Ihren Wünschen entspricht. Wenn Sie tiefer in die Benutzeranleitung von Furuno ETR-30N reinschauen, lernen Sie alle zugänglichen Produktfunktionen kennen, sowie erhalten Informationen über die Nutzung. Die Informationen, die Sie über Furuno ETR-30N erhalten, werden Ihnen bestimmt bei der Kaufentscheidung helfen.
Wenn Sie aber schon Furuno ETR-30N besitzen, und noch keine Gelegenheit dazu hatten, die Bedienungsanleitung zu lesen, sollten Sie es aufgrund der oben beschriebenen Gründe machen. Sie erfahren dann, ob Sie die zugänglichen Funktionen richtig genutzt haben, aber auch, ob Sie keine Fehler begangen haben, die den Nutzungszeitraum von Furuno ETR-30N verkürzen könnten.
Jedoch ist die eine der wichtigsten Rollen, die eine Bedienungsanleitung für den Nutzer spielt, die Hilfe bei der Lösung von Problemen mit Furuno ETR-30N. Sie finden dort fast immer Troubleshooting, also die am häufigsten auftauchenden Störungen und Mängel bei Furuno ETR-30N gemeinsam mit Hinweisen bezüglich der Arten ihrer Lösung. Sogar wenn es Ihnen nicht gelingen sollte das Problem alleine zu bewältigen, die Anleitung zeigt Ihnen die weitere Vorgehensweise – den Kontakt zur Kundenberatung oder dem naheliegenden Service.
