Benutzeranleitung / Produktwartung 4BQ des Produzenten EverFocus
Zur Seite of 12
E ver P lex 4BQ USER'S MANUAL Real time B/W quad processor High resolution picture quality 4 Alarm input with buzzer.
Notice This manual is presented to the users of EverPlex 4BQ by EverFocus Electronics Corp. With years of e ngineering researching, EverFocus has spared no effort to provide the high qua lity products to the worldwide users.
T able of Content Safety W arning ........... ............................................................... ................................. 1 Intr oduction................. .............................................................. ...........
1. To prevent fire or shock hazard , do not expose this equipment to the environment of high humidity and dust. Do not use it in an unprotected outdoor installation or any ar ea classified as a wet area. 2. Installation environment: The te mperature should be kept between 0 o C ~ +50 o C 3.
2 Introduction This B/W Quad processor repres ents the best choice for 4 cameras monitori ng and recording. 4 channel auto sequentia l switching with real time quad display, superior high resolution, and the most pr actical features in one convenient unit.
3 Specification Video input: Up to 4 cameras inputs and 1 VCR input Video output: 1 monitor output and 1 quad output for VCR 1Vp-p/75 ohm Refresh Rate: 15~30 fields/sec.
4 Chapter I Front Panel Keypads 1. Front Panel Keypads Seq 1.1 Full Screen Press any key of corresponding quadrant, the required channel will be displayed as full screen on the monit or. Press to go back to quad display. 1.2 Quad Display Press , the 4 camera input will be displayed in quad forma t on the ma i n monitor.
5 Chapter II Back Panel Function 1. BNC Conn ectors 1.1 Video In Connect camera video output to the corre sponding video in connector by a 75 ohm coaxial cable. 1.2 Video Out Connect the other device s to these conn ectors. They are used to loop through camera’s video to other devices.
6 4. Alarm Time Adjust the alarm holding time from 1 to 20 seconds. 5. Switch Time Adjust the auto sequential switc hing time from 1 to 10 seconds. 6. VCR Level The gain control regulator is used to ad just the brightness level of the VCR output. 7. Power Connect the AC 24V power source to the power input terminals.
7 8.1 Alarm out There are two ways to do the alarm out connection: 8.1.1 Normally Open Connection (use pin # 1 and # 9) 8 2 1 15 9 COIL 4 Channel B/W Quad Alarm out RELAY 8.
8 8.2 Alarm in There are 4 alarm sensors in for 4 channels, all these al arm inputs are Normally Open and shorted to ground means an alarm happens. 8 2 1 15 9 SENSOR 4 SENSOR 3 SENSOR 2 SENSOR 1 ALARM CIRCUIT There are four alarm i nputs for each camera.
EverFocus Electronics Corp. Head Office: 10F-6, No.79 Sec. 1 Shin-Tai Wu Road, Hsi-Chi, Taipei, Taiwan TEL: 886-2-26982334 FAX: 886-2-26982380 USA Office: 145 Vista Ave. Suite 108 Pasadena, CA. 91107 USA TEL: 1-626-844-8888 FAX: 1-626-844-8838 Toll free: 1-888-383-6287 or 1-888-EV-FOCUS Hong Kong Office: Room 0, 10/F.
Ein wichtiger Punkt beim Kauf des Geräts EverFocus 4BQ (oder sogar vor seinem Kauf) ist das durchlesen seiner Bedienungsanleitung. Dies sollten wir wegen ein paar einfacher Gründe machen:
Wenn Sie EverFocus 4BQ noch nicht gekauft haben, ist jetzt ein guter Moment, um sich mit den grundliegenden Daten des Produkts bekannt zu machen. Schauen Sie zuerst die ersten Seiten der Anleitung durch, die Sie oben finden. Dort finden Sie die wichtigsten technischen Daten für EverFocus 4BQ - auf diese Weise prüfen Sie, ob das Gerät Ihren Wünschen entspricht. Wenn Sie tiefer in die Benutzeranleitung von EverFocus 4BQ reinschauen, lernen Sie alle zugänglichen Produktfunktionen kennen, sowie erhalten Informationen über die Nutzung. Die Informationen, die Sie über EverFocus 4BQ erhalten, werden Ihnen bestimmt bei der Kaufentscheidung helfen.
Wenn Sie aber schon EverFocus 4BQ besitzen, und noch keine Gelegenheit dazu hatten, die Bedienungsanleitung zu lesen, sollten Sie es aufgrund der oben beschriebenen Gründe machen. Sie erfahren dann, ob Sie die zugänglichen Funktionen richtig genutzt haben, aber auch, ob Sie keine Fehler begangen haben, die den Nutzungszeitraum von EverFocus 4BQ verkürzen könnten.
Jedoch ist die eine der wichtigsten Rollen, die eine Bedienungsanleitung für den Nutzer spielt, die Hilfe bei der Lösung von Problemen mit EverFocus 4BQ. Sie finden dort fast immer Troubleshooting, also die am häufigsten auftauchenden Störungen und Mängel bei EverFocus 4BQ gemeinsam mit Hinweisen bezüglich der Arten ihrer Lösung. Sogar wenn es Ihnen nicht gelingen sollte das Problem alleine zu bewältigen, die Anleitung zeigt Ihnen die weitere Vorgehensweise – den Kontakt zur Kundenberatung oder dem naheliegenden Service.