Benutzeranleitung / Produktwartung QX-10 des Produzenten Epson
Zur Seite of 45
EPSON ® QX-10™ OPER ATIONS MANUAL.
FCC Compliance Statement for American Users This equipment generates and uses radio frequency energy and if not installed and used properly, that is, in strict accordance with the manufacturer’s instruc- tions, may cause interference to radio and television reception.
CONTENTS 1. Getting Started .................................. . 1 Unpacking ...................................... . 1 Getting Hooked Up ............................. . 3 Power .......................................... . 8 Booting ..................
3. Installing External Devices and Option Cards. .... . 25 Installing External Devices. ...................... . 25 External Device Ports. ....................... . 26 Checking the Cable. ........................ . 26 Plugging In .....................
Chapter 1 Getting Started Getting started with your QX-10™ won’t take very long at all. Even though there’s a good deal of material to go through, this chapter is simple and straightforward.
3. Environmental conditions. It’s important to keep your com- puter shielded from extremes in temperature, humidity, dust, and smoke. You’d be amazed at how smoke of any kind- cigarette, cigar, pipe, or even woodstove-can affect the in- tegrity of your diskettes.
Getting Hooked Up Now that all the boxes are unpacked, it’s time to put the parts together into a working system. Start with the main unit. That’s the one that looks like this: Place it on the flat surface with the front facing you, as shown.
The power switch is on the right side of the main unit, around the corner from the power outlet. It has two positions: ON and OFF. Important: Be sure the power switch is OFF before you hook up the QX-10.
The monitor cable is fairly short, with a cylindrical plug on either end. These are called DIN plugs. The monitor cable DIN plugs differ only in the number of pins inside: the end that connects to the back of the monitor has seven pins and the end that con- nects to back of the main unit has eight pins.
Insert the 7-pin plug into the outlet on the monitor and the other end into the round outlet on the back of the main unit, marked MONITOR. CABLE Now turn the main unit and monitor around so that they’re fac- ing you. The keyboard cable is coiled and looks like a phone cord.
PLUGGING IN KEYBOARD CABLE Some people like to use the QX-10 with the keyboard on their laps and others like to set it on a firm surface, but your options don’t end there. You can also adjust the angle of the keyboard. Changing the angle of the keyboard is simple.
Turn the keyboard right side up and try it for comfort. If the angle seems too steep, you can try the midway position by pushing each leg one notch further until it locks again.
Once you’ve powered up the computer, the small red light near the top right corner of the front of the main unit comes on and the cooling fan starts up (you can hear it). You may also notice that a number of small red lights on your keyboard blink on and off.
Booting Booting is the term used to describe the process of loading or transferring the operating system from the diskette into memory. Warm and Cold Booting A cold boot occurs when you power up the machine, or when you push the RESET button after inserting a new system diskette in drive A.
computer needs to run Valdocs. Data diskettes are where you store the information you created using the software on your system diskette. If you create a document (a letter or even a part of a novel!) using Valdocs, you store it on a data diskette. Caring For Your Diskettes Diskettes are wondrous things.
Make Backup Copies Often There’s no better way to protect your data than to have a spare copy tucked away in a safe place. If it’s particular- ly important data, you might want to have more than one copy. Some peo- ple even keep their backups in a safe deposit box.
the end of each day, all you have to do is take the disk marked for that day and copy your data onto it. For specific backup in- structions, refer to the user’s guide for your system. If you’re still unconvinced, just remember Murphy’s Law: If anything can go wrong, it will.
Beware of the Magnetic Field Remember that diskettes store their data magnetically, just like tapes. You probably won’t be running a horseshoe magnet over the surface of the diskette, but you should be aware that there are many sources of magnetism in and around your home or office.
If your QX-10 is not already turned ON, turn it ON now by press- ing the ON/OFF switch on the right side of the main unit. When the INSERT DISKETTE message appears on the screen, gently slide the system diskette into drive A, with the oval-shaped win- dow first and the label facing up.
Chapter 2 QX-10 Components If you’ve worked with computers before, much of the informa- tion in this manual probably comes as no surprise. If, on the other hand, you are new to computers, you may wonder if you have what it takes to master the QX-10.
A bit is a unit of computer information. Physically, it consists of a microscopic electrical switch that can be closed or open, representing the alternatives of yes or no, on or off, and so forth.
The QX-10 uses RAM-random access memory-which can be both written into and read. Normally RAM is lost when a com- puter is switched OFF, but the QX-10 has 2K of CMOS RAM, which enables it to retain some data when you turn OFF the power. (More about CMOS RAM later.
form as labelled. For example, when you press COPY DISK, the system copies the information on one disk to another disk. The DRAW key lets you create pie charts, bar graphs, and so on. The Video Monitor Your QX-10 has a special high-resolution green monochrome video monitor (also called a CRT, for cathode ray tube).
The video screen, in character mode, is 25 lines deep by 80 characters across. When in graphics mode, the screen gains very fine resolution. (Graphics displays are composed of tiny dots called pixels-for picture elements-and the QX-10 screen can display 640 pixels horizontally by 400 pixels vertical@, producing a sharp, clear graphics image.
Serial Port One serial port is available to connect external devices to the QX-10. The port is a standard RS-232C port; however, it can be changed under software control, by selecting the serial port op- tion from the SETUP program in either CP/M or Valdocs.
Light Pen Interface Another convenient feature is an interface for a light pen, which is a device used for tracing a diagram or object and producing the image on the screen, or for choosing a menu option on the screen. Option Cards The QX-10 has space for five peripheral, or option cards.
Chapter 3 Installing External Devices And Option Cards External devices such as printers, modems (for computer-to- computer communication over telephone lines), and speech syn- thesizers are all connected to the QX-10 through ports (outlets) built into the back of the main unit.
External Device Ports There are three external device ports on the back of the main unit: a light pen port, a Centronics-compatible parallel port (la- belled PRINTER), and an RS-232C serial port.
Plugging In Plug in the male end. Be careful! Connector prongs are easily bent. If the cable end doesn’t go in easily, it is probably upside down. Make sure you have the cable end right side up and try it again. Once the cable end is in, push it gently to make sure that it is in all the way.
Make sure you have: 1. The option card 2. The option card manual 3. A Phillips screwdriver. Powering Down Powering Down First, turn the power switch OFF. Then unplug the power cord from the wall outlet and turn the main unit around so that the back is facing you.
the front end. After the top is raised as far as it will go, you can lift it off. Set the cover aside. 29.
QX-l0 Interior: The Option Card Well The interior of the option card well looks like this: Removing the Shipping Brace The black metal plate is a shipping brace. It is easily removed by unscrewing the small Phillips screw on the inside. Store the screw and the brace in a safe place.
Selecting the Correct Slot For most option cards, it makes no difference which slot they are installed in. Occasionally, however, a card may require a specific slot. Check the option card manual to determine if your option card requires a specific slot.
Inserting the Option Card Slide the option card down into the proper slot, fitting the front end of the card into the corresponding notched guide on the front wall. Once the connector pins are seated in the connector slot, push a little more firmly to insert it fully.
main unit. Snap off the selected access slot while gripping the neighboring access slot(s) with your other hand. Now slide the remaining access slots back into place. Replacing the Cover With the cover in a vertical position, fit the two hinges into their holes on the front of the main unit, then lower the cover.
Powering Up Before you power up your QX-10, check to see that the power switch is OFF. Then plug the power cable into the wall outlet and turn the main unit around so that the front faces you. Now, unless your option card manual contains special instruc- tions, you’re ready to power up your QX-10.
Chapter 4 Troubleshooting Your QX-10 has been especially well-constructed, internally and externally, to be problem-free and damage-resistant. Occasionally though, even with the QX-10, things can go wrong. In many cases the problem is due to human factors-maybe you’re still mastering a new software package or option.
Does the second one work correctly? If so, the first one was prob- ably bad; save it and take it back to the supplier for a refund. But if the second (and all the rest) give the same undesirable results, go troubleshooting somewhere else-the odds are that you'll never buy a box of diskettes with more than one lemon in it.
Here are a few ways to find out whether you’ve got a real bug or not: First, if you have tried this routine many times before, and always successfully, then most likely it’s not a bug. Look for another cause for the trouble. A good approach is to start over from the very beginning.
DIP Switch Problems? There is a bank of eight DIP switches on the back of the main unit, between the monitor outlet and the speaker volume knob. Some software (such as Valdocs) might not work at all if the DIP switches are set incorrectly, or the software might give you a message on the monitor as to which switch(es) should be changed.
Options? If you have just installed an option card and you’re not getting the kind of results you expected, double-check the following: Is the option card inserted correctly? Did you follow the proc.
1. When everything is A-OK, your screen reads: INSERT DISKETTE 2. When there is an abnormality somewhere, and it’s time to call your Epson service center, you11 hear a buzzer and see the message: DIAGNOSTIC CODE 0001 with a 3-character suffix or you’ll hear the buzzer and see the message: DIAGNOSTIC CODE 0002 3.
Index Air circulation required for QX-10, 1 Application program, 19 Backup copies, 12-13 importance of making, 12 of system diskette, 12 system for making, 12-13 using to check disk, 35 Battery, 39 ni.
Human Applications Standard Computer Interface, see HASCI Humidity, excessive, avoiding, 2 If connector cable doesn’t go in easily, 27 If diskette doesn’t seem to go into drive correctly, 15 If op.
Printer, connecting to QX-10, 22, 26 problems with, 38 Problem, booting, 36 Problem, central processing unit, 40 Problem, DIP switch, 38 Problem, diskette, 35-36 checking against backup, 35 checking f.
Ein wichtiger Punkt beim Kauf des Geräts Epson QX-10 (oder sogar vor seinem Kauf) ist das durchlesen seiner Bedienungsanleitung. Dies sollten wir wegen ein paar einfacher Gründe machen:
Wenn Sie Epson QX-10 noch nicht gekauft haben, ist jetzt ein guter Moment, um sich mit den grundliegenden Daten des Produkts bekannt zu machen. Schauen Sie zuerst die ersten Seiten der Anleitung durch, die Sie oben finden. Dort finden Sie die wichtigsten technischen Daten für Epson QX-10 - auf diese Weise prüfen Sie, ob das Gerät Ihren Wünschen entspricht. Wenn Sie tiefer in die Benutzeranleitung von Epson QX-10 reinschauen, lernen Sie alle zugänglichen Produktfunktionen kennen, sowie erhalten Informationen über die Nutzung. Die Informationen, die Sie über Epson QX-10 erhalten, werden Ihnen bestimmt bei der Kaufentscheidung helfen.
Wenn Sie aber schon Epson QX-10 besitzen, und noch keine Gelegenheit dazu hatten, die Bedienungsanleitung zu lesen, sollten Sie es aufgrund der oben beschriebenen Gründe machen. Sie erfahren dann, ob Sie die zugänglichen Funktionen richtig genutzt haben, aber auch, ob Sie keine Fehler begangen haben, die den Nutzungszeitraum von Epson QX-10 verkürzen könnten.
Jedoch ist die eine der wichtigsten Rollen, die eine Bedienungsanleitung für den Nutzer spielt, die Hilfe bei der Lösung von Problemen mit Epson QX-10. Sie finden dort fast immer Troubleshooting, also die am häufigsten auftauchenden Störungen und Mängel bei Epson QX-10 gemeinsam mit Hinweisen bezüglich der Arten ihrer Lösung. Sogar wenn es Ihnen nicht gelingen sollte das Problem alleine zu bewältigen, die Anleitung zeigt Ihnen die weitere Vorgehensweise – den Kontakt zur Kundenberatung oder dem naheliegenden Service.
