Benutzeranleitung / Produktwartung 124T LTO-3 des Produzenten Dell
Zur Seite of 56
Dell™PowerVault™124TLTO - 3 Autoloader User's Guide Introduction Installing the Autoloader Operating the Autoloader Remote Management Unit Front Panel Administration Diagnostics Troubleshooting Technical Specifications Getting Help Notes, Notices, and Cautions Information in this document is subject to change without notice.
Back to Contents Page FrontPanelAdministration:Dell™PowerVault™124TLTO - 3 Autoloader User's Guide When you first power on the Dell PowerVault 124T LTO - 3 autoloader, it automatically runs a Power - On Self - Test (POST). During the POST, the left (green) LED flashes.
To configure the Dell PowerVault 124T LTO - 3 autoloader, you must verify the setup of the following: l SCSI ID(s). For the autoloader, there is a single SCSI ID. l Magazine(s). l Ethernet IP address (if you are not using DHCP). l SNMP server IP address — only if SNMP is being used.
l An IP gateway (optional) l A Simple Network Management Protocol (SNMP) server (optional) l A time server, or set the time and time zone manually (optional) Setting the IP Address An IP address is the address of any device attached to a network. Each device must have a unique IP address.
5. Press Enter . New Gateway is xxx.xxx.xxx.xxx appears on the LCD. You do not need to reboot the autoloader. 6. Press Escape or Enter to return to the Ethernet submenu. Setting the SNMP Server An SNMP server monitors a network by processing reporting activity in each network device (hub, router, bridge, and so on).
4. Scroll to set the number of hours difference between your local time and Greenwich Mean Time (GMT). 5. Scroll to set the number of minutes difference between your local time and GMT, then press Enter . The new time zone is set. 6. Press Escape or Enter as necessary to return to the main menu.
Setting Magazines In some cases, autoloader owners were being charged Independent Software Vendor (ISV) licensing fees for two - magazine autoloaders although only one magazine was configured. This occurred because the ISV software was registering the autoloader as a two - magazine device, regardless of the number of magazines configured.
Back to Contents Page.
Back to Contents Page Diagnostics:Dell™PowerVault™124TLTO - 3 Autoloader User's Guide Diagnostic Tests from the Front Panel Remote Management Unit Diagnostic Tests Dia.
2. Scroll to the test you want to run and press Enter . If you are already logged in as Administrator, the test begins executing immediately. The message Running Test appears while the test is running. 3. If you are not logged in, you will be asked to enter the Administrator password.
Back to Contents Page GettingHelp:Dell™PowerVault™124TLTO - 3 Autoloader User's Guide Technical Assistance Dell Enterprise Training and Certification Pr.
www.dell.com/jp (Japan only) www.euro.dell.com (Europe only) www.dell.com/la (Latin American countries) www.dell.ca (Canada only) l Anonymous file transfer protocol (FTP) ftp.dell.com/ Log in as user:anonymous , and use your e - mail address as your password.
Automated Order - Status Service TocheckonthestatusofanyDell™productsthatyouhaveordered,youcangoto support.dell.com , or you can call the automated order - status service. A recording prompts you for the information needed to locate and report on your order.
Before You Call If possible, turn on your system before you call Dell for technical assistance and call from a telephone at or near the computer. You may be asked to type some commands at the keyboard, relay detailed information during operations, or try other troubleshooting steps possible only at the computer system itself.
Back to Contents Page InstallingtheAutoloader:Dell™PowerVault™124TLTO - 3 Autoloader User's Guide Installation Overview Installing the autoloader consists of the following steps, which are explained in more detail later in this section: 1.
l Bar code labels l TORX L - key drivers (T8 and T10) l Emergency Magazine Removal Tool Choosing a Location Choose a location that meets the following criteria (see " Technical Specifications "): UL Requirements Bar Code Reader Your autoloader is equipped with a bar code reader.
Back Panel Overview Unpacking the Autoloader Before you begin, clear a desk or table so that you can unpack the autoloader. You also need to select an open 2U computer rack location near the server that will host the autoloader. Unpack and inspect the autoloader for shipping damage by doing the following: 1.
Connecting the SCSI and Power Cables To connect the SCSI and power cables to the autoloader, follow these steps: 1. Shut down and turn off the selected server.
Preparing the Host and Verifying the Connection If necessary, install a SCSI host adapter, software, and compatible drivers. Refer to the manuals for the host computer and SCSI host adapter for detailed instructions.
Manager . The LTO - 3 drive should be listed under the ? Other Devices item as IBM ULTRIUM - TD3 SCSI Sequential Device . 4. Right - click the IBM ULTRIUM - TD3 SCSI Sequential Device listing and click Properties . 5. Select the Driver tab. 6. Click Update Driver .
10. Click Next again to install the driver. 11. Click Finish . 12. Close the Device Properties dialog box. The autoloader now appears in Device Manager under Medium Changers as a Dell (tm) PowerVault (tm) 124T Autoloader , and is ready to use.
LOAD ADPT160M.HAM SLOT=201 /LUNS LOAD ADPT160M.HAM SLOT=202 /LUNS 6. After the STARTUP.NCF file has been edited, save the file and reboot the server to activate the new STARTUP.NCF. 7. Upon reboot navigate to the System Console and type scan all . This will start a scan of all the LUNS on each adapter.
Back to Contents Page Introduction:Dell™PowerVault™124TLTO - 3 Autoloader User's Guide Overview Data backup is essential to protect irreplaceable information. Backing up data to magnetic tape is an easy, cost - efficient method used by many small and medium businesses.
Back to Contents Page OperatingtheAutoloader:Dell™PowerVault™124TLTO - 3 Autoloader User's Guide Operator's Panel Functionality Using Cartridges Using Magaz.
Using Cartridges Typically, when you first install the autoloader, you load your cartridges into the magazines and then load the magazines into the autoloader.
Ejecting a Single Cartridge When you want to remove a single cartridge from the autoloader, you can specify the cartridge you want by bar code or location, or choose the cartridge currently in the tape drive. To eject a cartridge by bar code: 1. From the main menu, scroll to Commands , and then press Enter .
The autoloader will not run unless both magazine bays are properly occupied with either a magazine or a magazine blank. One way that you can close the openings is to use two magazines. If you use only one magazine, then you must fill the other magazine opening with a magazine blank for the unit to become operational.
There are two white thumbwheels, located on each end of the magazine. You can move the slots within the magazine by turning these two white thumbwheels and aligning a slot with one of the two openings. Do not rotate the magazine by inserting your hand and pushing the cartridge carriers.
Viewing Firmware Version To view the current firmware version, use the following procedure: 1. From the main menu, scroll to Status , and then press Enter . 2. From the Status submenu, scroll to Autoloader , and then press Enter . 3. From the Autoloader submenu, scroll to Version , and then press Enter .
Viewing Ethernet Information To view the Ethernet information, use the following procedure. 1. From the main menu, scroll to Status , and then press Enter . 2. From the Status submenu, scroll to Ethernet , and then press Enter . A list of messages appears.
Back to Contents Page RemoteManagementUnit:Dell™PowerVault™124TLTO - 3 Autoloader User's Guide Remote Management Unit Overview Configuration Page Firmware Page .
Remote Management Unit (RMU) Web Interface Status Pane 1. System Status - provides model and serial number (S/N) of both the autoloader and the drive. This section also contains the Dell Service Tag number. You will need this number if you call for technical support.
SCSI ID You can change the drive's SCSI ID from the Remote Management Unit. To change the SCSI ID: 1. From any page, click the Configuration heading. The Configuration screen displays. 2. Under System Operations , select SCSI ID . 3. Click the drop - down box to select a number to assign for the new SCSI ID.
handled by the backup package you have installed instead. 4. Click submit . Setting the Magazines This setting is used to report the number of storage elements and the element address to the SCSI host. This setting must match the physical configuration in order for correct information to be reported.
system, the IP address may change depending on the network administrator's settings. To Set IP address: 1. Clear the check box to remove the check mark from the DHCP field, if applicable. 2. In the IP address fields, type the static IP address using the <Tab> key to move from box to box.
4. Type the IP addresses in the appropriate boxes. 5. Click submit to save. Client Overlap Control is a management policy on controlling how the Web server handles overlapping control requests from multiple clients on the authorized client list. The options include No Locking , Full Locking , and Time - Based Locking .
1. From any page, click the Diagnostics heading. The Diagnostics screen will be displayed. 2. Under View Error and History Logs , click View Logs . You can also save the logs to a file by clicking Save Logs . If you save the logs to a file, you must select a destination folder within 60 seconds.
1. From any page, click the Library Operations heading. The Library Operations screen displays. 2. From the Library Operations page, click Inventory . The autoloader starts an inventory immediately.
Back to Contents Page TechnicalSpecifications:Dell™PowerVault™124TLTO - 3 Autoloader User's Guide Physical Specifications Autoloader Performance Specifications .
Autoloader Power Specifications Autoloader Vibration Specifications Autoloader Shock Specifications Tape Drive Specifications LTO - 3 Drive Specifications Media Capacity Media Specific.
Back to Contents Page Troubleshooting:Dell™PowerVault™124TLTO - 3 Autoloader User's Guide Before Contacting Customer Support Operator Control Panel Error Display Check.
Operator Control Panel Error Display The Operator Control Panel (OCP) is used for operator input, and to display status and error information output. Errors generated by the autoloader hardware result in error codes unique to the Dell PowerVault 124T.
l No error message appears, but the autoloader fails to complete the action. When either of these things occur, the system generates a log of the error. You can use these error logs to determine the type of error, when it occurred, and what parts of the autoloader it affects.
15 Timer Error 16 Tick Error 17 Activate Error 18 Threshold Error 19 Suspend Lifted 1A Block Pool Error 1B Queue Function Failed 1C Semaphore Function Failed 1D Timer Function Failed 1F Thread Functio.
l If the Picker Test failed, verify there is no obstruction within the picker assembly and repeat the test. l If the Random Moves test failed, see steps above for necessary actions. l Power cycle the autoloader and re - run the failed test. Contact support.
l Verify that the network is properly configured (i.e. no loop - back condition exists). l Verify that the autoloader operates correctly when properly configured and attached directly to a host system using a cross - over cable. l If all previous steps fail, contact support.
l Check host adapter and SCSI cables and terminator. l Power cycle the autoloader and retry the operation. l If all previous steps fail, contact support.
location. l Power cycle the autoloader through the front panel. l Run the Random Moves test from either the Remote Management Unit (RMU) or the Operator Control Panel (OCP). Note: The Random Moves test requires a minimum of two cartridges present within the autoloader.
l Power cycle the autoloader. l Run the Random Moves test from either the Remote Management Unit (RMU) or the Operator Control Panel (OCP). Note: The Random Moves test requires a minimum of two cartridges present within the autoloader. l If all previous steps fail, contact support.
E9 Time Update Event The system time was changed. No action required. Front Panel Error Types EA LCD Busy Error Possible LCD controller problem, software error, or communication error. l Power cycle the autoloader. l Run the Random Moves test. l If all previous steps fail, contact support.
TapeAlert Logs You can retrieve TapeAlert log information through one of three methods: l Operator Control Panel (OCP) l Remote Management Unit (RMU) display to screen l Detailed logs saved to text file through the RMU for call center diagnosis Further information and recommended actions for tape drive TapeAlerts can be found in Table 3 .
Tape Alert Message Typical Application Client Message Probable Cause Of Error Message Recommended Action Drive TAflag[01] Read Warning TapeAlert Log Entry: 8000000000000000 The tape drive is having problems reading data. No data has been lost, but there has been a reduction in the performance of the tape.
Unrecoverable Mechanical Cartridge Failure TapeAlert Log Entry: 0004000000000000 in the drive has experienced a mechanical failure. cartridge mechanical failure in the drive where medium cannot be de - mounted.
Drive TAflag[28] Power Consumption TapeAlert Log Entry: 0000001000000000 The tape drive power consumption is outside the specified range. Power consumption of the tape drive is outside specified range. Drive TAflag[29] Drive Maintenance TapeAlert Log Entry: 0000000800000000 Preventive maintenance of the tape drive is required.
Returning the Autoloader for Service If you need to return the autoloader or a component of the autoloader for service, contact support.dell.com . The following steps will help you to prepare the autoloader for shipment, remove the autoloader from a rack, and package the autoloader.
Packing the Autoloader Gather the original packaging material to pack the autoloader: the shipping box, two foam end caps, accessory package insert (placed at the back of the unit), and the antistatic bag. You will also need packing tape. 1. Place the antistatic bag over the autoloader.
Ein wichtiger Punkt beim Kauf des Geräts Dell 124T LTO-3 (oder sogar vor seinem Kauf) ist das durchlesen seiner Bedienungsanleitung. Dies sollten wir wegen ein paar einfacher Gründe machen:
Wenn Sie Dell 124T LTO-3 noch nicht gekauft haben, ist jetzt ein guter Moment, um sich mit den grundliegenden Daten des Produkts bekannt zu machen. Schauen Sie zuerst die ersten Seiten der Anleitung durch, die Sie oben finden. Dort finden Sie die wichtigsten technischen Daten für Dell 124T LTO-3 - auf diese Weise prüfen Sie, ob das Gerät Ihren Wünschen entspricht. Wenn Sie tiefer in die Benutzeranleitung von Dell 124T LTO-3 reinschauen, lernen Sie alle zugänglichen Produktfunktionen kennen, sowie erhalten Informationen über die Nutzung. Die Informationen, die Sie über Dell 124T LTO-3 erhalten, werden Ihnen bestimmt bei der Kaufentscheidung helfen.
Wenn Sie aber schon Dell 124T LTO-3 besitzen, und noch keine Gelegenheit dazu hatten, die Bedienungsanleitung zu lesen, sollten Sie es aufgrund der oben beschriebenen Gründe machen. Sie erfahren dann, ob Sie die zugänglichen Funktionen richtig genutzt haben, aber auch, ob Sie keine Fehler begangen haben, die den Nutzungszeitraum von Dell 124T LTO-3 verkürzen könnten.
Jedoch ist die eine der wichtigsten Rollen, die eine Bedienungsanleitung für den Nutzer spielt, die Hilfe bei der Lösung von Problemen mit Dell 124T LTO-3. Sie finden dort fast immer Troubleshooting, also die am häufigsten auftauchenden Störungen und Mängel bei Dell 124T LTO-3 gemeinsam mit Hinweisen bezüglich der Arten ihrer Lösung. Sogar wenn es Ihnen nicht gelingen sollte das Problem alleine zu bewältigen, die Anleitung zeigt Ihnen die weitere Vorgehensweise – den Kontakt zur Kundenberatung oder dem naheliegenden Service.
